* added thingspulse gateways
* added thingspulse gateways, RGB LED for tinypico
* Added some LED and Birghtness options
* Requested Changes
* fixed format
so as to don't disclose the password used for WM.
Also change the wm password from MAc to be the last 8 digits, as these will change more than the first 8 ones.
Also make consistent the ifndef qnd the parsing between WM_PWD_FROM_MAC and USE_MAC_AS_GATEWAY_NAME
* First draft of LM75 sensor based on HTU21 sensor
* Initialise I2C on ESP8266
* Add LM75 sensor to test builds
So that it will be tested with the continuous integration
* Add RGB Led management for errors, infos, and send receive events
Add RGB led management for indicators, integrate it for M5 Atom and ESP32 C3 and S3 dev board
Update Fastled version to 3.5.0.
The default behavior is with regular LED, to use RGB Led the macro RGB_INDICATORS needs to be define, along with the FASTLED_IND_TYPE, FASTLED_IND_DATA_GPIO and FASTLED_IND_NUM_LEDS
Note that some RGB led need to have a different color scheme, so in this case it can be entered along with the data PIN definition: -DFASTLED_IND_DATA_GPIO=27,GRB
* Add FastLed library to the environments
* Handle OTA actively when MQTT is not connected
Resolves#1292
* Fix compilation for targets not having OTA
* ArduinoOTA.handle() only with non-ESP targets
* OTA check before reboot: fix condition and add more comments
Signed-off-by: Sami Salonen <ssalonen@gmail.com>
The main features of the upgrade to 0.1.3 of rtl_433_ESP are
1 - Change Transceiver Library to RadioLib
2 - Add support for SX127X transceiver module ( I used the 433 Mhz version of this Heltec module for development ).
3 - Added automatic calibration of the RSSI Signal detection Threshold
4 - Removed dependency on loop for start and end of signal detection, and moved to a ESP32 Task
5 - Moved received signal decoding to a ESP32 Task
6 - Identified Blueline PowerCost Monitor decoder as source of significant memory overhead and disabled.
7 - Multi Receiver support has been validated with RF, RF2 and PiLight
* Publishing/receiving inconsistencies
* General platformio.ini changes
General platformio.ini changes to allow for publishing/receiving settings to be defined in User_cofig.h instead of them only working if defined in the environments. Kept separate so far for discussion.
* Behaviour when MQTT and/or Wifi is not available
I was looking into why all my OpenMQTTGateway devices were not responding after a recent power failure and am speculating that the ESP32 was able to restart faster than my Wifi and MQTT Server was able to restart and resume operations. And was thinking that a generic ESP.restart may be a reasonable approach with repeated Wifi and/or MQTT connection failures.
As mentioned here https://community.openmqttgateway.com/t/behaviour-when-mqtt-and-or-wifi-is-not-available/1747
Added new variable maxRetryWatchDog, which is the maximum number of mqtt or wifi connection attempts before restarting gateway device.
* Allow for hiding mqtt config settings in wifimanager setup.
Adds the macro `WIFIMNG_HIDE_MQTT_CONFIG` that when defined will hide the mqtt configuration in the wifimanager setup.
Co-authored-by: Florian <1technophile@users.noreply.github.com>
When updating from the MQTT command from a SSL enabled server this adds an option to provide
the server SSL certificate with the command.
This is useful if connecting to different servers or if the configured certificate has expired
and requires updating to not lose the ability to update via OTA.
The certificate provided will be saved to flash memory for use on subsequent restarts.
This allows for setting the WiFimanager debug level for more or less verbosity using the WM_DEBUG_LEVEL macro.
Valid values are:
DEBUG_ERROR = 0,
DEBUG_NOTIFY = 1, // default
DEBUG_VERBOSE = 2,
DEBUG_DEV = 3,
DEBUG_MAX = 4
Adds the macro USE_MAC_AS_GATEWAY_NAME, when defined the gateway name will default to
OMG_XXXXXXXXXXXX, where the X's are the mac address characters.
This can still be changed in WiFiManager.
* Fixes BLE scanning being disabled after switching server fails.
* Fixes crash caused by BLE scan results arriving while switching servers.
* Adds documentation to use the server switching command.
Merges LED_RECEIVE/LED_SEND into LED_SEND_RECEIVE pin definition.
Adds LED_ERROR to display error status based on blink times as follows:
Disconnected from Wifi: 2 seconds on 2 seconds off.
Disconnected from broker: 2 seconds on 5 seconds off.
Other status LED indications added:
WifiManager configuration web portal active: LED_INFO and LED_SEND_RECEIVE = ON.
OTA Update in progress: LED_SEND_RECIEVE and LED_ERROR = ON.
This adds the ability to specify if the MQTT broker connection is secure via a checkbox on the config page of WiFiManager.
Also added to the WiFiManager config page is a text box to enter the brokers TLS certificate.
In the case of using manual configuration a new macro is created MQTT_SECURE_DEFAULT.
When defined as true a secure connection will be requested and the certificate defined in user_config.h will be used.
If enabled in user_config.h this will trigger the OMG to update it's firmware from the link
provided in the MQTT message.
Example message:
{\"version\":\"test\",\"password\":\"OMGPASSWORD\",\"url\":\"https://github.com/1technophile/OpenMQTTGateway/releases/download/v0.9.6/esp32dev-ble-cont-firmware.bin\"}
If the firmware version in the message is not the same as the current OMG version the device will self update using the link in the url of the message.
* Increased ESP32 base capabilities
1 - Expose SERIAL_BAUD as an optional compiler directive.
2 - Enabled mDNS based MQTT Host name lookup for ESP32 devices.
3 - Expand capability of ESPWifiManualSetup mode for multiple SSID’s.
Tested with ESP32
* Regression testing of ESP8266 and ESP32
* Removal of Wifi Debuging
* Fix lint issue
Co-authored-by: Northern Man <sgracey@Heisenberg.local>
* Support for changing CC1101 Receive and Transmit Frequency
* Docs
* Resolve feedback
* Update Somfy module to use Global receiveMhz
ELECHOUSE_cc1101.SpiStrobe(CC1101_SIDLE); // Idle receiver prior to
setting a new frequency
* Correct buffer processing
was missing an instruction due to a previous refactoring
* Correct duplicate condition
* Avoid publishing \n into the raw value
* Merge extract_char and value_from_service_data functions
* Initial generalization from a PWM LED controller, to a PWM controller.
Allow the config file to set the name of each channel and the number of channels.
Fade time is now per-channel, so MQTT messages can genuinely set an individual channel, and specify the fade time for that channel.
The default gamma is configurable in the config.
Charles