* Disable MQTTsetMQTT and MQTT_HTTPS_FW_UPDATE to allow OTA for Avatto Bakery IR
Trying to update my Avattos with the currently released 0.9.8 I found that OTA wasn't possible any longer as the build was now to large
0.9.8
Checking size .pio/build/avatto-bakeey-ir/firmware.elf
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM: [==== ] 42.4% (used 34772 bytes from 81920 bytes)
Flash: [====== ] 55.2% (used 528716 bytes from 958448 bytes)
this goes back to 0.9.7, where WiFi, MQTT and firmware update was introduced over MQTT commands
0.9.7
Checking size .pio/build/avatto-bakeey-ir/firmware.elf
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM: [==== ] 42.4% (used 34772 bytes from 81920 bytes)
Flash: [====== ] 55.2% (used 528716 bytes from 958448 bytes)
Going back to building 0.9.6 I was able to OTA update again with the much smaller build
0.9.6
Checking size .pio/build/avatto-bakeey-ir/firmware.elf
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM: [==== ] 39.7% (used 32512 bytes from 81920 bytes)
Flash: [==== ] 41.4% (used 396804 bytes from 958448 bytes)
Building 0.9.8 with the flags brings the build back to OTAable size
0.9.8 with
'-UMQTTsetMQTT'
'-UMQTT_HTTPS_FW_UPDATE'
Checking size .pio/build/avatto-bakeey-ir/firmware.elf
Advanced Memory Usage is available via "PlatformIO Home > Project Inspect"
RAM: [==== ] 39.9% (used 32684 bytes from 81920 bytes)
Flash: [==== ] 42.3% (used 405024 bytes from 958448 bytes)
Similar to the flag setting in [env:rfbridge]
I'm not even sure if MQTT_HTTPS_FW_UPDATE would even work on the Avatto, with the limited flash memory.
Should we also add
board_build.ldscript = eagle.flash.1m64.ld
as a default, as it's required for OTA updates on the Avattos as discussed in https://github.com/1technophile/OpenMQTTGateway/issues/763#issuecomment-698864712 ?
* Doc addition for restricted MQTT options
Doc addition for https://github.com/1technophile/OpenMQTTGateway/pull/1046 and https://github.com/1technophile/OpenMQTTGateway/pull/986
* Define MQTTsetMQTT for configuring MQTT over MQTT
* Enable MQTTsetMQTT per default on all ESP except RFBridge
Co-authored-by: Dave <d.kneisz@gmail.com>
This will enable using button on the gateway to switch any controlled attached actuators/relays when pressed.
Adds the following macros:
- ACTUATOR_ON; 0 or 1, set to the output level of the gpio pin to turn the actuator on.
- ACTUATOR_ONOFF_DEFAULT; ACTUATOR_ON or !ACTUATOR_ON, set to the state desired on reset.
- ACTUATOR_BUTTON_TRIGGER_LEVEL; 0 or 1, set to the sensing level which to detect a button press to change the actuator state.
This adds the ability to specify if the MQTT broker connection is secure via a checkbox on the config page of WiFiManager.
Also added to the WiFiManager config page is a text box to enter the brokers TLS certificate.
In the case of using manual configuration a new macro is created MQTT_SECURE_DEFAULT.
When defined as true a secure connection will be requested and the certificate defined in user_config.h will be used.
* Update to SmartRC-CC1101-Driver-Lib@^2.5.4 and removal of workaround from #847
Tks to @LSatan workaround no longer needed
https://github.com/LSatan/SmartRC-CC1101-Driver-Lib/issues/65
* Default to value as subject for rtl_433 and receiver switching
* Default to not publishing unparsed signals
* Fix for missing String for uint64_t
* Fix is only required when value a subject is defined and not PiLight
Co-authored-by: Northern Man <sgracey@Heisenberg.local>
If enabled in user_config.h this will trigger the OMG to update it's firmware from the link
provided in the MQTT message.
Example message:
{\"version\":\"test\",\"password\":\"OMGPASSWORD\",\"url\":\"https://github.com/1technophile/OpenMQTTGateway/releases/download/v0.9.6/esp32dev-ble-cont-firmware.bin\"}
If the firmware version in the message is not the same as the current OMG version the device will self update using the link in the url of the message.
* PR #934
* Active Receiver Switching
Switching of the active receiver module is available between the RF,
RF2, RTL_433 and Pilight Gateway modules, allowing for changing of
signal decoders without redploying the openMQTTGateway package.
Sending a JSON message to the command topic of the desired receiver
will change the active receiver module.
Other minor adjustments/improvements
1 - Improved startup serial logging that includes
- OpenMQTTGateway Version
- OpenMQTTGateway Modules
2 - Trace logging of full Gateway module command topic
- Enabled in RF, RF2, PiLight and RTL_433
3 - Updated RTL_433 Documentation to only include enabled ASK/OOK
device decoders
4 - Trace logging of MQTT Callback topic
* Regression testing
* Adding valueAsASubject support to rtl_433_ESP
- model and id keys are appended to message topic
* Increased memory size for receiver switching in blocking build all
Co-authored-by: Northern Man <sgracey@Heisenberg.local>
* BLE low power mode and settings optimization
-low power mode settings example
-take into account parameters following #891
-add esp32dev-ble-cont for door/window sensor listening
* Disable WDT during scan
* update esp32 arduino framework
* Support for changing CC1101 Receive and Transmit Frequency
* Docs
* Resolve feedback
* Update Somfy module to use Global receiveMhz
ELECHOUSE_cc1101.SpiStrobe(CC1101_SIDLE); // Idle receiver prior to
setting a new frequency
* Initial generalization from a PWM LED controller, to a PWM controller.
Allow the config file to set the name of each channel and the number of channels.
Fade time is now per-channel, so MQTT messages can genuinely set an individual channel, and specify the fade time for that channel.
The default gamma is configurable in the config.
-replace low power led by led info
-enable to change the led ON value
-go upper case for the led macros
Also transform BLE connect warning to notice in log
Add Sonoff RF Bridge LED
* Add LYWSD03MMC and MHO-C401 device
and an associated BLE connect mechanism as these devices advertise only encrypted data
-free manufacturer data
-update library
* Implement scans number before connect
-Add the possibility to do a connect every X scan
-Rename variables for consistency
-Some refactoring for improved code reading
* added support for secure TLS connections
on ESP32 and ESP8266 close#101
* added TLS test builds
* added documentation for TLS
fixed some some issues in the documentation
* added documentation for error code=54
DigiH