58 lines
2.7 KiB
Markdown
58 lines
2.7 KiB
Markdown
# Sensors
|
|
Subscribe to all the messages with mosquitto or open your MQTT client software:
|
|
|
|
` sudo mosquitto_sub -t +/# -v`
|
|
|
|
### ADC
|
|
The value is between 0 and 1024 and is transmitted via MQTT when it changes.
|
|
`home/OpenMQTTGateway/ADCtoMQTT {"value":543}`
|
|
|
|
### DHT
|
|
You will receive every TimeBetweenReadingDHT (set into config_DHT.h) the DHT measurement (30s per default).
|
|
|
|
`home/OpenMQTTGateway/DHTtoMQTT {"tempc":21,"tempf":69.8,"hum":51}`
|
|
|
|
Legacy (removed after release 0.9.5)
|
|
`home/OpenMQTTGateway/DHTtoMQTT {"temp":21,"hum":51}`
|
|
|
|
If you want to don't resend value when it is the same you can set dht_always = false in config_DHT.h
|
|
|
|
### HTU21
|
|
You will receive the HTU21 sensor readings every TimeBetweenReadinghtu21 (set into config_HTU21.h) (30s by default).
|
|
|
|
`home/OpenMQTTGateway/CLIMAtoMQTT/htu {"tempc":25.34064,"tempf":77.61314,"hum":56.53052}`
|
|
|
|
If you don't want to resend values that haven't changed you can set htu21_always = false in config_HTU21.h
|
|
|
|
### AHTx0 (AHT10 and AHT20)
|
|
You will receive the AHT sensor readings every TimeBetweenReadingAHTx0 (set into config_AHTx0.h) (30s by default).
|
|
|
|
`home/OpenMQTTGateway/CLIMAtoMQTT/aht { "tempc": 27.48108, "tempf": 81.46594, "hum": 48.90614 }`
|
|
|
|
If you don't want to resend values that haven't changed you can set AHTx0_always = false in config_AHTx0.h
|
|
|
|
### DS18x20
|
|
You will receive the DS18x20 sensor readings every DS1820_INTERVAL_SEC (set into config_DS1820.h) (60s by default).
|
|
Each sensor will be published under the following topic using each sensors' address.
|
|
|
|
`home/OpenMQTTGateway/CLIMAtoMQTT/ds1820/0x0000000000000000 {"tempc":27.8, "tempf":82.04, "type":"DS18B20","res":"12bit\n","addr":"0x28616411907650bc"}`
|
|
|
|
Legacy (removed after release 0.9.5)
|
|
`home/OpenMQTTGateway/CLIMAtoMQTT/ds1820/0x0000000000000000 {"temp":27.8,"unit":"C","type":"DS18B20","res":"12bit\n","addr":"0x28616411907650bc"}`
|
|
|
|
The units for temperature readings are sent in Celsius by default can be changed to Fahrenheit by setting DS1820_FAHRENHEIT = true in in config_DS1820.h
|
|
|
|
If you don't want to resend values that haven't changed you can set DS1820_ALWAYS = false in config_DS1820.h
|
|
|
|
### HCSR501
|
|
A boolean value of the PIR sensors state is sent when a state change occurs. The length of time that the PIR stays in a triggered state depends on the PIR hardware and is not changed by OpenMQTTGateway.
|
|
|
|
`home/OpenMQTTGateway/HCSR501toMQTT {"presence":"false"}`
|
|
|
|
You can have another PIN mirror the value of the PIR sensor output by adding the following to config_HCSR501.h
|
|
This can be useful if you would like to connect an LED to turn on when motion is detected.
|
|
|
|
`#define HCSR501_LED_NOTIFY_GPIO 4`
|
|
|
|
This notification pin can be inverted if driving directly or through a transistor/mosfet.
|
|
`#define INVERT_LED_NOTIFY true` |