This allows for connecting to devices that do not use the MAC address type 0.
This also adds the logging of the "mac_type" so it is visible to users trying to connect to broadcasting devices.
Additionally this will allow for future connectable devices using a MAC address type other than 0 to be automatically connected to
when support is added for them, similar to LYWSD03MMC etc..
* Remove std::string as the model id and use decoder enum.
* Update decoder version
* Check model id is in decoder range when launching discovery.
* Add BLEconnect enum MIN/MAX
* Add immediate parameter to BLE connection commands.
When sending a command to read/write a characteristic on a BLE server this adds a new parameter to cause the action to be
performed immediately. This will stop the scan in progress to perform the actions queued.
Example use:
```
mosquitto_pub -t home/OpenMQTTGateway/commands/MQTTtoBT/config -m '{
"ble_write_address":"AA:BB:CC:DD:EE:FF",
"ble_write_service":"cba20d00-224d-11e6-9fb8-0002a5d5c51b",
"ble_write_char":"cba20002-224d-11e6-9fb8-0002a5d5c51b",
"ble_write_value":"TEST",
"value_type":"STRING",
"ttl":4,
"immediate":true }'
```
Stop BLE processing when immeditate command sent.
* Use a shorter connection timeout.
* Update docs.
* Remove MQTT spam for connection retrys
* Prevent crashing when the normal connection process occurs at the same time as an immediate action.
* Use a semaphore to protect BLE device vector.
This will remove the sending of BLE service data when multiple service data attributes are advertised by a broadcasting device.
Instead the data for known device types will be consolidated into a single message to reduce overhead.
* Fixes BLE scanning being disabled after switching server fails.
* Fixes crash caused by BLE scan results arriving while switching servers.
* Adds documentation to use the server switching command.
* EXPERIMENTAL: Ble read/write characteristics over MQTT.
Uses #979
This allows reading and writing BLE characteristics from an MQTT message.
Example format:
mosquitto_pub -t home/OpenMQTTGateway/commands/MQTTtoBT/config -m '{"ble_write_address":"AA:BB:CC:DD:EE:FF", "ble_write_service":"cba20d00-224d-11e6-9fb8-0002a5d5c51b", "ble_write_char":"cba20002-224d-11e6-9fb8-0002a5d5c51b", "ble_write_value":"TEST", "ttl":4 }'
mosquitto_pub -t home/OpenMQTTGateway/commands/MQTTtoBT/config -m '{"ble_read_address":"30:AE:A4:7C:3C:A6", "ble_read_service":"cba20d00-224d-11e6-9fb8-0002a5d5c51b", "ble_read_char":"cba20002-224d-11e6-9fb8-0002a5d5c51b", "ttl": 2 }'
The ttl parameter is the number of calls to connect (defaults to 1), which occur after the BLE scan completes.
A response is provided over MQTT in the format:
write : {"id":"30:AE:A4:7C:3C:A6","service":"cba20d00-224d-11e6-9fb8-0002a5d5c51b","characteristic":"cba20002-224d-11e6-9fb8-0002a5d5c51b","write":"TEST","success":true}
read : {"id":"30:AE:A4:7C:3C:A6","service":"cba20d00-224d-11e6-9fb8-0002a5d5c51b","characteristic":"cba20002-224d-11e6-9fb8-0002a5d5c51b","read":"TEST","success":true}
* Add generic BLE connect class and read data as hex.
* Add value_type parameter and document usage
* Add note to docs
With the additional functionality added by @h2zero I’m able to extract
the temperate data from the 2nd part of the bluetooth message.
Co-authored-by: Northern Man <sgracey@Heisenberg.local>
Using NimBLE requires less resources than bluedroid so it is much less beneficial to
deinitialize the stack. Instead this initializes it once in initial setup and only deinitializes
before entering deep sleep.
* BLE low power mode and settings optimization
-low power mode settings example
-take into account parameters following #891
-add esp32dev-ble-cont for door/window sensor listening
* Disable WDT during scan
* update esp32 arduino framework
Useful if you want to scan continuously for BLE device, in this case you should deactivate the BLE connect to avoid concurrency between scan and connect
Amy Nagle