Merges LED_RECEIVE/LED_SEND into LED_SEND_RECEIVE pin definition.
Adds LED_ERROR to display error status based on blink times as follows:
Disconnected from Wifi: 2 seconds on 2 seconds off.
Disconnected from broker: 2 seconds on 5 seconds off.
Other status LED indications added:
WifiManager configuration web portal active: LED_INFO and LED_SEND_RECEIVE = ON.
OTA Update in progress: LED_SEND_RECIEVE and LED_ERROR = ON.
* EXPERIMENTAL: Ble read/write characteristics over MQTT.
Uses #979
This allows reading and writing BLE characteristics from an MQTT message.
Example format:
mosquitto_pub -t home/OpenMQTTGateway/commands/MQTTtoBT/config -m '{"ble_write_address":"AA:BB:CC:DD:EE:FF", "ble_write_service":"cba20d00-224d-11e6-9fb8-0002a5d5c51b", "ble_write_char":"cba20002-224d-11e6-9fb8-0002a5d5c51b", "ble_write_value":"TEST", "ttl":4 }'
mosquitto_pub -t home/OpenMQTTGateway/commands/MQTTtoBT/config -m '{"ble_read_address":"30:AE:A4:7C:3C:A6", "ble_read_service":"cba20d00-224d-11e6-9fb8-0002a5d5c51b", "ble_read_char":"cba20002-224d-11e6-9fb8-0002a5d5c51b", "ttl": 2 }'
The ttl parameter is the number of calls to connect (defaults to 1), which occur after the BLE scan completes.
A response is provided over MQTT in the format:
write : {"id":"30:AE:A4:7C:3C:A6","service":"cba20d00-224d-11e6-9fb8-0002a5d5c51b","characteristic":"cba20002-224d-11e6-9fb8-0002a5d5c51b","write":"TEST","success":true}
read : {"id":"30:AE:A4:7C:3C:A6","service":"cba20d00-224d-11e6-9fb8-0002a5d5c51b","characteristic":"cba20002-224d-11e6-9fb8-0002a5d5c51b","read":"TEST","success":true}
* Add generic BLE connect class and read data as hex.
* Add value_type parameter and document usage
* Add note to docs
With the additional functionality added by @h2zero I’m able to extract
the temperate data from the 2nd part of the bluetooth message.
Co-authored-by: Northern Man <sgracey@Heisenberg.local>
- Adds MQTT command to change the WiFi access point.
- Adds MQTT command to change the MQTT broker and update username and password.
This will test the connection changes first and, if unsuccessful, fallback to the current connection.
If successful the new configuration will be saved in non-volatile memory.
This adds the ability to specify if the MQTT broker connection is secure via a checkbox on the config page of WiFiManager.
Also added to the WiFiManager config page is a text box to enter the brokers TLS certificate.
In the case of using manual configuration a new macro is created MQTT_SECURE_DEFAULT.
When defined as true a secure connection will be requested and the certificate defined in user_config.h will be used.
* Update to SmartRC-CC1101-Driver-Lib@^2.5.4 and removal of workaround from #847
Tks to @LSatan workaround no longer needed
https://github.com/LSatan/SmartRC-CC1101-Driver-Lib/issues/65
* Default to value as subject for rtl_433 and receiver switching
* Default to not publishing unparsed signals
* Fix for missing String for uint64_t
* Fix is only required when value a subject is defined and not PiLight
Co-authored-by: Northern Man <sgracey@Heisenberg.local>
If enabled in user_config.h this will trigger the OMG to update it's firmware from the link
provided in the MQTT message.
Example message:
{\"version\":\"test\",\"password\":\"OMGPASSWORD\",\"url\":\"https://github.com/1technophile/OpenMQTTGateway/releases/download/v0.9.6/esp32dev-ble-cont-firmware.bin\"}
If the firmware version in the message is not the same as the current OMG version the device will self update using the link in the url of the message.
Using NimBLE requires less resources than bluedroid so it is much less beneficial to
deinitialize the stack. Instead this initializes it once in initial setup and only deinitializes
before entering deep sleep.
* PR #934
* Active Receiver Switching
Switching of the active receiver module is available between the RF,
RF2, RTL_433 and Pilight Gateway modules, allowing for changing of
signal decoders without redploying the openMQTTGateway package.
Sending a JSON message to the command topic of the desired receiver
will change the active receiver module.
Other minor adjustments/improvements
1 - Improved startup serial logging that includes
- OpenMQTTGateway Version
- OpenMQTTGateway Modules
2 - Trace logging of full Gateway module command topic
- Enabled in RF, RF2, PiLight and RTL_433
3 - Updated RTL_433 Documentation to only include enabled ASK/OOK
device decoders
4 - Trace logging of MQTT Callback topic
* Regression testing
* Adding valueAsASubject support to rtl_433_ESP
- model and id keys are appended to message topic
* Increased memory size for receiver switching in blocking build all
Co-authored-by: Northern Man <sgracey@Heisenberg.local>
* Increased ESP32 base capabilities
1 - Expose SERIAL_BAUD as an optional compiler directive.
2 - Enabled mDNS based MQTT Host name lookup for ESP32 devices.
3 - Expand capability of ESPWifiManualSetup mode for multiple SSID’s.
Tested with ESP32
* Regression testing of ESP8266 and ESP32
* Removal of Wifi Debuging
* Fix lint issue
Co-authored-by: Northern Man <sgracey@Heisenberg.local>
h2zero