[BT] Bump Theengs Decoder to 1.6.4 & NUTALE added as presence tracker (#1818)

• Bump Theengs Decoder to 1.6.4
• NUTALE added as presence tracker
• Small doc changes

README.md

@@ -25,7 +25,7 @@ Upload OpenMQTTGateway directly from the [upload page](https://docs.openmqttgate
 
 ### Theengs Bridge, BLE gateway with external antenna
 
-[Theengs bridge](https://shop.theengs.io/products/theengs-bridge-esp32-ble-mqtt-gateway-with-ethernet-and-external-antenna) is a powerfull BLE to MQTT gateway for over [80 sensors](https://decoder.theengs.io/devices/devices.html). Equipped with an Ethernet port, and external antenna, ensuring an enhanced range for your BLE sensors. It supports also WiFi connectivity.
+[Theengs bridge](https://shop.theengs.io/products/theengs-bridge-esp32-ble-mqtt-gateway-with-ethernet-and-external-antenna) is a powerfull BLE to MQTT gateway for over [90 sensors](https://decoder.theengs.io/devices/devices.html). Equipped with an Ethernet port, and external antenna, ensuring an enhanced range for your BLE sensors. It supports also WiFi connectivity.
 
 [![Theengs bridge view](./docs/img/Theengs-Bridge-ble-gateway.png)](https://shop.theengs.io/products/theengs-bridge-esp32-ble-mqtt-gateway-with-ethernet-and-external-antenna)
 

docs/README.md

@@ -60,7 +60,7 @@ Under the hood, OpenMQTTGateway offers features such as:
 
 ### Theengs Bridge, BLE gateway with external antenna
 
-[Theengs bridge](https://shop.theengs.io/products/theengs-bridge-esp32-ble-mqtt-gateway-with-ethernet-and-external-antenna) is a powerfull BLE to MQTT gateway for over [80 sensors](https://decoder.theengs.io/devices/devices.html). Equipped with an Ethernet port, and external antenna, ensuring an enhanced range for your BLE sensors. It supports also WiFi connectivity.
+[Theengs bridge](https://shop.theengs.io/products/theengs-bridge-esp32-ble-mqtt-gateway-with-ethernet-and-external-antenna) is a powerfull BLE to MQTT gateway for over [90 sensors](https://decoder.theengs.io/devices/devices.html). Equipped with an Ethernet port, and external antenna, ensuring an enhanced range for your BLE sensors. It supports also WiFi connectivity.
 
 [![Theengs bridge view](./img/Theengs-Bridge-ble-gateway.png)](https://shop.theengs.io/products/theengs-bridge-esp32-ble-mqtt-gateway-with-ethernet-and-external-antenna)
 

docs/prerequisites/board.md

@@ -15,7 +15,7 @@ If you want to use the BLE decoding capabilities of OpenMQTTGateway with a Raspb
 If you want to use the BLE decoding capabilities of OpenMQTTGateway with a tablet or smartphone you can use [Theengs App](https://app.theengs.io/).
 :::
 
-[Theengs bridge](https://shop.theengs.io/products/theengs-bridge-esp32-ble-mqtt-gateway-with-ethernet-and-external-antenna) is a powerfull BLE to MQTT gateway for over [80 sensors](https://decoder.theengs.io/devices/devices.html). Equipped with an Ethernet port, and external antenna, ensuring an enhanced range for your BLE sensors. It supports also WiFi connectivity.
+[Theengs bridge](https://shop.theengs.io/products/theengs-bridge-esp32-ble-mqtt-gateway-with-ethernet-and-external-antenna) is a powerful BLE to MQTT gateway for over [90 sensors](https://decoder.theengs.io/devices/devices.html). Equipped with an Ethernet port, and external antenna, ensuring an enhanced range for your BLE sensors. It supports also WiFi connectivity.
 
 [![Theengs bridge view](../img/Theengs-Bridge-ble-gateway.png)](https://shop.theengs.io/products/theengs-bridge-esp32-ble-mqtt-gateway-with-ethernet-and-external-antenna)
 

docs/upload/builds.md

@@ -111,7 +111,7 @@ upload_flags =
 ::: warning Note
 Adding manual WiFi and MQTT credentials to an environment also requires to define
 `'-DESPWifiManualSetup=true'`
-for the credetials to be registered correctly.
+for the credentials to be registered correctly.
 :::
 
 ::: warning Note
@@ -236,7 +236,7 @@ upload_flags =
 * Choose the board on the Arduino IDE
 * Select the port corresponding to the board
 * Note that for using BLE on ESP32 you will need to select *Minimal SPIFFS* into Tools->Partition Scheme
-* Open the serial monitor and set 115200 bauds
+* Open the serial monitor and set 115200 baud
 * Upload ➡️
 * You should see the logs in the serial monitor
 

docs/use/boards.md

@@ -14,7 +14,7 @@ On M5Stack boards you may do a long press to these buttons in low power mode 0 (
 You can also do a long press when powering the board to reset it, this press must be done during the first 5 seconds after the start.
 
 ### Wifi interference on sensors when using an ESP ###
-Certain sensors like HC-SR501 is prone to generate false signals / triggers when used on a ESP with Wifi enabled. To reduce or elimate the effect the board must be put into Wifi B/G with lower TX power.
+Certain sensors like HC-SR501 is prone to generate false signals / triggers when used on a ESP with Wifi enabled. To reduce or eliminate the effect the board must be put into Wifi B/G with lower TX power.
 
 This can be achieved with the following macro, `WifiGMode` defined true and `WifiPower` to e.g. WIFI_POWER_11dBm (ESP32) or 11 (ESP8266).  
 

docs/use/rf.md

@@ -60,7 +60,7 @@ This feature is only available on a ESP32 based device with a supported transcei
 ### Supported hardware combinations
 
 - ESP32 based device with a CC1101 transceiver
-- Heltec WiFi LoRa 32 (V2.1) and LilyGo Lora 32 V2.1
+- Heltec WiFi LoRa 32 (V2.1) and LilyGo LoRa 32 V2.1
 - ESP32 DOIT DevKit V1 and Ai-Thinker R01 (SX1278)
 - ESP32 + SX1278/SX1276
 

main/ZgatewayBT.ino

@@ -404,6 +404,7 @@ void updateDevicesStatus() {
     unsigned long now = millis();
     // Device tracker devices
     if (BTConfig.presenceEnable && (p->sensorModel_id == TheengsDecoder::BLE_ID_NUM::NUT ||
+                                    p->sensorModel_id == TheengsDecoder::BLE_ID_NUM::NUTALE ||
                                     p->sensorModel_id == TheengsDecoder::BLE_ID_NUM::MIBAND ||
                                     p->sensorModel_id == TheengsDecoder::BLE_ID_NUM::TAGIT ||
                                     p->sensorModel_id == TheengsDecoder::BLE_ID_NUM::TILE ||
@@ -976,6 +977,7 @@ void launchBTDiscovery(bool overrideDiscovery) {
             p->sensorModel_id < TheengsDecoder::BLE_ID_NUM::BLE_ID_MAX &&
             p->sensorModel_id != TheengsDecoder::BLE_ID_NUM::HHCCJCY01HHCC && p->sensorModel_id != TheengsDecoder::BLE_ID_NUM::BM2) { // Exception on HHCCJCY01HHCC and BM2 as these ones are discoverable and connectable
           if (p->sensorModel_id == TheengsDecoder::BLE_ID_NUM::NUT ||
+              p->sensorModel_id == TheengsDecoder::BLE_ID_NUM::NUTALE ||
               p->sensorModel_id == TheengsDecoder::BLE_ID_NUM::MIBAND ||
               p->sensorModel_id == TheengsDecoder::BLE_ID_NUM::TAGIT ||
               p->sensorModel_id == TheengsDecoder::BLE_ID_NUM::TILE ||

platformio.ini

@@ -154,7 +154,7 @@ somfy_remote=Somfy_Remote_Lib@0.3.0
 rtl_433_ESP = https://github.com/NorthernMan54/rtl_433_ESP.git#v0.3.1
 emodbus =  miq19/eModbus@1.0.0
 gfSunInverter = https://github.com/BlackSmith/GFSunInverter.git#v1.0.1
-decoder = https://github.com/theengs/decoder.git#v1.6.3
+decoder = https://github.com/theengs/decoder.git#v1.6.4
 ssd1306 = https://github.com/ThingPulse/esp8266-oled-ssd1306.git#f96fd6a
 lm75 = jeremycole/I2C Temperature Sensors derived from the LM75@^1.0.3
 rn8209 = https://github.com/theengs/RN8209C-SDK.git#arduino