Add SHELLY PLUS 1 board with support of relay, switch, BT gateway (#1349)

So that you know, the overtemperature protection is not implemented in the firmware.

.github/workflows/build.yml

@@ -47,6 +47,7 @@ jobs:
           - "ttgo-t-beam"
           - "heltec-wifi-lora-32-868"
           - "heltec-wifi-lora-32-915"
+          - "shelly-plus1"
           - "nodemcuv2-all-test"
           - "nodemcuv2-fastled-test"
           - "nodemcuv2-2g"

docs/upload/web-install.md

@@ -47,6 +47,7 @@ The table below describes the libraries and the modules of each board configurat
 |esp32dev-somfy-CC1101|ESP32 dev board|Gateway using [Somfy Remote](https://github.com/Legion2/Somfy_Remote_Lib) library, need CC1101|X|-|-|-|
 |esp32dev-weatherstation|ESP32 dev board|Gateway to retrieve weather station data Ventus W174/W132 (tested), Auriol H13726, Hama EWS 1500, Meteoscan W155/W160 using [WeatherStationDataRx](https://github.com/Zwer2k/WeatherStationDataRx)|X|-|-|-|
 |esp32feather-ble|ESP32 Feather Adafruit|BLE for the Adafruit Feather board|-|-|X|-|
+|shelly-plus1|Shelly Plus 1 relay board|BLE, Relay control, Switch|-|-|X|-|
 |heltec-wifi-lora32-868|ESP32 HELTEC LORA V2|LORA communication 868Mhz  using [arduino-LoRA](https://github.com/sandeepmistry/arduino-LoRa) |-|-|-|X|
 |heltec-wifi-lora32-915|ESP32 HELTEC LORA V2|LORA communication 915Mhz using [arduino-LoRA](https://github.com/sandeepmistry/arduino-LoRa)|-|-|-|X|
 |heltec-rtl_433|ESP32 HELTEC LORA32 v2|Gateway using [RTL_433_ESP](https://github.com/NorthernMan54/rtl_433_ESP) and [RadioLib](https://github.com/jgromes/RadioLib)|X|-|-|-|

main/ZactuatorONOFF.ino

@@ -103,13 +103,16 @@ void MQTTtoONOFF(char* topicOri, char* datacallback) {
 }
 #  endif
 
-void ActuatorButtonTrigger() {
-  uint8_t level = !digitalRead(ACTUATOR_ONOFF_GPIO);
-  char* level_string = "ON";
-  if (level != ACTUATOR_ON) {
-    level_string = "OFF";
+void ActuatorManualTrigger(uint8_t level) {
+#  ifdef ACTUATOR_BUTTON_TRIGGER_LEVEL
+  if (level == ACTUATOR_BUTTON_TRIGGER_LEVEL) {
+    // Change level value to the opposite of the current level
+    level = !digitalRead(ACTUATOR_ONOFF_GPIO);
   }
-  Log.trace(F("Actuator triggered %s by button" CR), level_string);
+#  else
+  level = !digitalRead(ACTUATOR_ONOFF_GPIO);
+#  endif
+  Log.trace(F("Actuator triggered %d" CR), level);
   digitalWrite(ACTUATOR_ONOFF_GPIO, level);
   // Send the state of the switch to the broker so as to update the status
   StaticJsonDocument<JSON_MSG_BUFFER> jsonBuffer;

main/ZsensorGPIOInput.ino

@@ -34,11 +34,11 @@ unsigned long resetTime = 0;
 #  endif
 unsigned long lastDebounceTime = 0;
 int InputState = 3; // Set to 3 so that it reads on startup
-int lastInputState = 3;
+int previousInputState = 3;
 
 void setupGPIOInput() {
   Log.notice(F("Reading GPIO at pin: %d" CR), INPUT_GPIO);
-  pinMode(INPUT_GPIO, INPUT_PULLUP); // declare GPIOInput pin as input_pullup to prevent floating. Pin will be high when not connected to ground
+  pinMode(INPUT_GPIO, GPIO_INPUT_TYPE); // declare GPIOInput pin as input_pullup to prevent floating. Pin will be high when not connected to ground
 }
 
 void MeasureGPIOInput() {
@@ -49,7 +49,7 @@ void MeasureGPIOInput() {
   // since the last press to ignore any noise:
 
   // If the switch changed, due to noise or pressing:
-  if (reading != lastInputState) {
+  if (reading != previousInputState) {
     // reset the debouncing timer
     lastDebounceTime = millis();
   }
@@ -75,7 +75,6 @@ void MeasureGPIOInput() {
 #  endif
     // if the Input state has changed:
     if (reading != InputState) {
-      InputState = reading;
       Log.trace(F("Creating GPIOInput buffer" CR));
       StaticJsonDocument<JSON_MSG_BUFFER> jsonBuffer;
       JsonObject GPIOdata = jsonBuffer.to<JsonObject>();
@@ -88,15 +87,15 @@ void MeasureGPIOInput() {
       if (GPIOdata.size() > 0)
         pub(subjectGPIOInputtoMQTT, GPIOdata);
 
-#  ifdef ZactuatorONOFF
-      if (InputState == ACTUATOR_BUTTON_TRIGGER_LEVEL) {
-        ActuatorButtonTrigger();
-      }
+#  if defined(ZactuatorONOFF) && defined(ACTUATOR_TRIGGER)
+      //Trigger the actuator if we are not at startup
+      if (InputState != 3) ActuatorManualTrigger(InputState);
 #  endif
+      InputState = reading;
     }
   }
 
-  // save the reading. Next time through the loop, it'll be the lastInputState:
-  lastInputState = reading;
+  // save the reading. Next time through the loop, it'll be the previousInputState:
+  previousInputState = reading;
 }
 #endif

main/config_GPIOInput.h

@@ -42,6 +42,10 @@ extern void GPIOInputtoMQTT();
 #  endif
 #endif
 
+#ifndef GPIO_INPUT_TYPE
+#  define GPIO_INPUT_TYPE INPUT_PULLUP
+#endif
+
 #define INPUT_GPIO_ON_VALUE  "HIGH"
 #define INPUT_GPIO_OFF_VALUE "LOW"
 

main/config_ONOFF.h

@@ -41,7 +41,10 @@ extern void MQTTtoONOFF(char* topicOri, JsonObject& RFdata);
 #endif
 //#  define ACTUATOR_ONOFF_DEFAULT !ACTUATOR_ON // ACTUATOR_ON or !ACTUATOR_ON, set to the state desired on reset.
 #ifndef ACTUATOR_BUTTON_TRIGGER_LEVEL
-#  define ACTUATOR_BUTTON_TRIGGER_LEVEL LOW // 0 or 1, set to the sensing level which to detect a button press to change the actuator state.
+//#  define ACTUATOR_BUTTON_TRIGGER_LEVEL LOW // 0 or 1, set to the sensing level which to detect a button press to change the actuator state.
+#endif
+#ifndef ACTUATOR_TRIGGER
+#  define ACTUATOR_TRIGGER false // false or true, enable to control an actuator directly from the board switch (default behavior if true), or by button if ACTUATOR_BUTTON_TRIGGER_LEVEL is defined
 #endif
 
 /*-------------------PIN DEFINITIONS----------------------*/

platformio.ini

@@ -61,6 +61,7 @@ extra_configs =
 ;default_envs = tinypico-ble
 ;default_envs = ttgo-lora32-v1-868
 ;default_envs = ttgo-lora32-v1-915
+;default_envs = shelly-plus1
 ;default_envs = ttgo-t-beam
 ;default_envs = heltec-wifi-lora-32-868
 ;default_envs = heltec-wifi-lora-32-915
@@ -159,6 +160,7 @@ monitor_speed = 115200
 esp8266_platform = espressif8266@3.2.0
 esp32_platform = espressif32@3.5.0
 esp32_c3_s3_platform = espressif32@5.2.0
+esp32_solo_platform = https://github.com/tasmota/platform-espressif32/releases/download/v.2.0.5/platform-espressif32-v.2.0.5.zip
 atmelavr_platform = atmelavr@3.3.0
 
 [com-esp]
@@ -1020,6 +1022,37 @@ build_flags =
   '-DTimeLedON=0.1'
   '-DLED_SEND_RECEIVE_ON=1'
 
+[env:shelly-plus1]
+platform = ${com.esp32_solo_platform}
+board = esp32-solo1
+board_build.partitions = min_spiffs.csv
+lib_deps =
+  ${com-esp.lib_deps}
+  ${libraries.ble}
+  ${libraries.wifimanager32}
+  ${libraries.decoder}
+build_flags = 
+  ${env.build_flags}
+  ${com-esp.build_flags}
+  '-DZgatewayBT="BT"'
+  '-DTimeBtwRead=100'
+  '-DScan_duration=3000'
+  '-DTRIGGER_GPIO=25'
+  '-DZactuatorONOFF="ONOFF"'
+  '-DACTUATOR_ON=1'
+  '-DACTUATOR_OFF=0'
+  '-ACTUATOR_TRIGGER=true'
+  '-DZsensorGPIOInput="GPIOInput"'
+  '-DINPUT_GPIO=4'
+  '-DGPIO_INPUT_TYPE=INPUT'
+  '-DACTUATOR_ONOFF_GPIO=26'
+  '-DZsensorADC="ADC"'
+  '-DADC_GPIO=32'
+  '-DUSE_MAC_AS_GATEWAY_NAME'
+  '-DFRAMEWORK_ARDUINO_SOLO1'
+  '-DGATEWAY_MANUFACTURER="Shelly"'
+  '-DGATEWAY_MODEL="SPLUS1"'
+
 [env:nodemcuv2-all-test]
 platform = ${com.esp8266_platform}
 board = nodemcuv2
@@ -1324,6 +1357,7 @@ build_flags =
   '-DACTUATOR_ON=0'
   '-DACTUATOR_ONOFF_DEFAULT=ACTUATOR_ON'
   '-DACTUATOR_BUTTON_TRIGGER_LEVEL=0'
+  '-ACTUATOR_TRIGGER=true'
   '-DGateway_Name="OpenMQTTGateway_SONOFF_RELAY"'
 board_build.flash_mode = dout
 
@@ -1344,6 +1378,7 @@ build_flags =
   '-DACTUATOR_ON=0'
   '-DACTUATOR_ONOFF_DEFAULT=ACTUATOR_ON'
   '-DACTUATOR_BUTTON_TRIGGER_LEVEL=0'
+  '-ACTUATOR_TRIGGER=true'
   '-DRF_RECEIVER_GPIO=4'
   '-DZgatewayRF="RF"'
   '-DGateway_Name="OpenMQTTGateway_SONOFF_BASIC_RFR3"'

scripts/gen_wu.py

@@ -119,7 +119,7 @@ with open(manif_path + filename,'wb') as output_file:
 
 for item in range(len(assets)):
     name = assets[item]['name']
-    if 'firmware.bin' in name and ('esp32' in name or 'ttgo' in name or 'heltec' in name or 'thingpulse' in name or 'lilygo' in name):
+    if 'firmware.bin' in name and ('esp32' in name or 'ttgo' in name or 'heltec' in name or 'thingpulse' in name or 'lilygo' in name or 'shelly' in name):
         fw = name.split('-firmware')[0]
         man_file = fw + '.manifest.json'
         fw_url = assets[item]['browser_download_url']

scripts/gen_wu_dev.py

@@ -107,7 +107,7 @@ with open(manif_path + filename,'wb') as output_file:
     output_file.write(boot_bin.content)
 
 for name in os.listdir(bin_path):
-    if 'firmware.bin' in name and ('esp32' in name or 'ttgo' in name or 'heltec' in name or 'thingpulse' in name or 'lilygo' in name):
+    if 'firmware.bin' in name and ('esp32' in name or 'ttgo' in name or 'heltec' in name or 'thingpulse' in name or 'lilygo' in name or 'shelly' in name):
         fw = name.split('-firmware')[0]
         man_file = fw + '.manifest.json'
         print('Bin name:' + name)