FlorianandFlorian
3187ed6154
Add Serial as a communication layer so as to transmit data to/from serial Enable discovery of BT sensors through serial Add serial heartbeat Change discovery principle for interval and intervalacts, keep them always discovered and deactivate adaptivescan when changed. Instead of removing their discovery when adaptive scan is activated Increase JSON_MSG_BUFFER_MAX as we are now using const char* and it requires more memory for Arduino Json Deserialization Co-authored-by: Florian <1technophile@users.noreply.github.com>
80 lines
3.1 KiB
C
80 lines
3.1 KiB
C
/*
|
|
OpenMQTTGateway - ESP8266 or Arduino program for home automation
|
|
|
|
Act as a gateway between your 433mhz, infrared IR, BLE, LoRa signal and one interface like an MQTT broker
|
|
Send and receiving command by MQTT
|
|
|
|
This files enables to set your parameter for the radiofrequency gateways (ZgatewayRF and ZgatewayRF2) with RCswitch and newremoteswitch library
|
|
|
|
Copyright: (c)Florian ROBERT
|
|
|
|
This file is part of OpenMQTTGateway.
|
|
|
|
OpenMQTTGateway is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
OpenMQTTGateway is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
#ifndef config_RFM69_h
|
|
#define config_RFM69_h
|
|
|
|
extern void setupRFM69();
|
|
extern bool RFM69toX();
|
|
extern void XtoRFM69(const char* topicOri, const char* datacallback);
|
|
extern void XtoRFM69(const char* topicOri, JsonObject& RFdata);
|
|
/*----------------------RFM69 topics & parameters -------------------------*/
|
|
// Topic where the message from RFM69 will be published by the gateway,
|
|
// appended with the nodeID of the sender
|
|
#define subjectRFM69toMQTT "/RFM69toMQTT"
|
|
|
|
// Topic subscribed by the gateway. Messages received will be sent to RFM69
|
|
#define subjectMQTTtoRFM69 "/commands/MQTTtoRFM69"
|
|
#define RFM69receiverKey "RCV_" // receiver id will be defined if a subject contains RFM69receiverKey followed by a value of 3 digits
|
|
// On reception of an ack from RFM69, the message that has been sent is published here
|
|
#define subjectGTWRFM69toMQTT "/RFM69toMQTT/acked"
|
|
#define defaultRFM69ReceiverId 99
|
|
|
|
// Default values
|
|
const char PROGMEM ENCRYPTKEY[] = "sampleEncryptKey";
|
|
const char PROGMEM MDNS_NAME[] = "rfm69gw1";
|
|
const char PROGMEM MQTT_BROKER[] = "raspi2";
|
|
const char PROGMEM RFM69AP_NAME[] = "RFM69-AP";
|
|
#define NETWORKID 200 //the same on all nodes that talk to each other
|
|
#define NODEID 10
|
|
|
|
//Match frequency to the hardware version of the radio
|
|
#define FREQUENCY RF69_433MHZ
|
|
//#define FREQUENCY RF69_868MHZ
|
|
//#define FREQUENCY RF69_915MHZ
|
|
#define IS_RFM69HCW true // set to 'true' if you are using an RFM69HCW module
|
|
#define POWER_LEVEL 31
|
|
|
|
/*-------------------PIN DEFINITIONS----------------------*/
|
|
#if defined(ESP8266)
|
|
# define RFM69_CS D1
|
|
# define RFM69_IRQ D8 // GPIO15/D8
|
|
# define RFM69_IRQN digitalPinToInterrupt(RFM69_IRQ)
|
|
# define RFM69_RST D4 // GPIO02/D4
|
|
#elif defined(ESP32)
|
|
# define RFM69_CS 1
|
|
# define RFM69_IRQ 8 // GPIO15/D8
|
|
# define RFM69_IRQN digitalPinToInterrupt(RFM69_IRQ)
|
|
# define RFM69_RST 4 // GPIO02/D4
|
|
#else
|
|
//RFM69 not tested with arduino
|
|
# define RFM69_CS 10
|
|
# define RFM69_IRQ 0
|
|
# define RFM69_IRQN digitalPinToInterrupt(RFM69_IRQ)
|
|
# define RFM69_RST 9
|
|
#endif
|
|
|
|
#endif
|