Florian
7c6e0ccf61
* esp32 init * RF gateway ok with ESP32 * correct IR gateway compilation errors and test RF2 ok * divide config per board type * update test file according user_config * differentiate variable type following IR libraries aka platforms * implement BLE beacons detection with ESP32 * Implement multitasking on BLE gateway * Library add and change core assignement * change core assignement for BLE * add mi flora value readings with ESP32 * adding some traces and removing unecessary comment * correct compilation error due to pin assignement * correct temperature float value and wrong mac adress rssi publishing * add esp32 to CI * correct esp32 ide retrieving * correcting paths * CI: correct architecture * libraries update (irremote) and overwrite ble library files
70 lines
3.0 KiB
C
70 lines
3.0 KiB
C
/*
|
|
OpenMQTTGateway - ESP8266 or Arduino program for home automation
|
|
|
|
Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker
|
|
Send and receiving command by MQTT
|
|
|
|
This files enables to set your parameter for the radiofrequency gateways (ZgatewayRF and ZgatewayRF2) with RCswitch and newremoteswitch library
|
|
|
|
Copyright: (c)Florian ROBERT
|
|
|
|
This file is part of OpenMQTTGateway.
|
|
|
|
OpenMQTTGateway is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
OpenMQTTGateway is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
/*----------------------RFM69 topics & parameters -------------------------*/
|
|
// Topic where the message from RFM69 will be published by the gateway,
|
|
// appended with the nodeID of the sender
|
|
#define subjectRFM69toMQTT "home/RFM69toMQTT"
|
|
// Upon reception of a packed, the RSSI of that packet will be publish to this topic,
|
|
// appended with the nodeID of the sender
|
|
#define subjectRFM69toMQTTrssi "home/RFM69toMQTT/rssi" // Comment this if you don't want the RSSI to be published.
|
|
#define subjectRFM69toMQTTsender "home/RFM69toMQTT/sender"
|
|
// Topic subscribed by the gateway. Messages received will be sent to RFM69
|
|
#define subjectMQTTtoRFM69 "home/commands/MQTTtoRFM69"
|
|
#define RFM69receiverKey "RCV_" // receiver id will be defined if a subject contains RFM69receiverKey followed by a value of 3 digits
|
|
// On reception of an ack from RFM69, the message that has been sent is published here
|
|
#define subjectGTWRFM69toMQTT "home/RFM69toMQTT/acked"
|
|
#define defaultRFM69ReceiverId 99
|
|
|
|
// Default values
|
|
const char PROGMEM ENCRYPTKEY[] = "sampleEncryptKey";
|
|
const char PROGMEM MDNS_NAME[] = "rfm69gw1";
|
|
const char PROGMEM MQTT_BROKER[] = "raspi2";
|
|
const char PROGMEM RFM69AP_NAME[] = "RFM69-AP";
|
|
#define NETWORKID 200 //the same on all nodes that talk to each other
|
|
#define NODEID 10
|
|
|
|
//Match frequency to the hardware version of the radio
|
|
#define FREQUENCY RF69_433MHZ
|
|
//#define FREQUENCY RF69_868MHZ
|
|
//#define FREQUENCY RF69_915MHZ
|
|
#define IS_RFM69HCW true // set to 'true' if you are using an RFM69HCW module
|
|
#define POWER_LEVEL 31
|
|
|
|
/*-------------------PIN DEFINITIONS----------------------*/
|
|
#if defined(ESP8266) || defined(ESP32)
|
|
#define RFM69_CS D1
|
|
#define RFM69_IRQ D8 // GPIO15/D8
|
|
#define RFM69_IRQN digitalPinToInterrupt(RFM69_IRQ)
|
|
#define RFM69_RST D4 // GPIO02/D4
|
|
#else
|
|
//RFM69 not tested with arduino
|
|
#define RFM69_CS 10
|
|
#define RFM69_IRQ 0
|
|
#define RFM69_IRQN digitalPinToInterrupt(RFM69_IRQ)
|
|
#define RFM69_RST 9
|
|
#endif
|