Florian
441ab1c0b7
* some minor correction after coadcy checks * Put serial communication speed as a parameter in user_config.h * complete gateway file receiving ok sending ko #32 * add rfm69 to CI * change receiver key and minor improvments #32 now ok on receiving and sending with RFM69 * add schema and tested pinout for RFM69/RF/IR wiring #32 * RFM69 library add * Implement newremoteswitchlibrary for KlikAanKlikUit / ClickOnClickOff protocol #3 * add dependency for CI and link to the library * compilation error for arduino correction * Sketch size decrease * remove nano from CI * Divide user_config into one file per gateway/sensor for lisibility
55 lines
2.1 KiB
C
55 lines
2.1 KiB
C
/*
|
|
OpenMQTTGateway - ESP8266 or Arduino program for home automation
|
|
|
|
Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker
|
|
Send and receiving command by MQTT
|
|
|
|
This files enables to set your parameter for the BME280 sensor
|
|
|
|
Copyright: (c) Hans-Juergen Dinges
|
|
|
|
This file is part of OpenMQTTGateway.
|
|
|
|
OpenMQTTGateway is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
OpenMQTTGateway is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
|
|
Connection Schemata:
|
|
--------------------
|
|
|
|
BH1750 ------> Arduino Uno ----------> ESP8266
|
|
==============================================
|
|
Vcc ---------> 5V -------------------> Vu (5V)
|
|
GND ---------> GND ------------------> GND
|
|
SCL ---------> Pin A5 ---------------> D1
|
|
SDA ---------> Pin A4 ---------------> D2
|
|
ADD ---------> N/C (Not Connected) --> N/C (Not Connected)
|
|
|
|
*/
|
|
|
|
#define bme280_always true // if false when the current value for light Level (Lux) is the same as previous one don't send it by MQTT
|
|
#define TimeBetweenReadingbme280 30000
|
|
|
|
/*----------------------------USER PARAMETERS-----------------------------*/
|
|
/*-------------DEFINE YOUR MQTT PARAMETERS BELOW----------------*/
|
|
#define TEMPBMEC "home/CLIMAtoMQTT/bme/tempc"
|
|
#define TEMPBMEF "home/CLIMAtoMQTT/bme/tempf"
|
|
#define HUMBME "home/CLIMAtoMQTT/bme/hum"
|
|
#define PRESSBME "home/CLIMAtoMQTT/bme/pa"
|
|
#define ALTIBMEM "home/CLIMAtoMQTT/bme/altim"
|
|
#define ALTIBMEFT "home/CLIMAtoMQTT/bme/altift"
|
|
|
|
//Time used to wait for an interval before resending measured values
|
|
unsigned long timebme280 = 0;
|
|
|
|
|