Florian
7c6e0ccf61
* esp32 init * RF gateway ok with ESP32 * correct IR gateway compilation errors and test RF2 ok * divide config per board type * update test file according user_config * differentiate variable type following IR libraries aka platforms * implement BLE beacons detection with ESP32 * Implement multitasking on BLE gateway * Library add and change core assignement * change core assignement for BLE * add mi flora value readings with ESP32 * adding some traces and removing unecessary comment * correct compilation error due to pin assignement * correct temperature float value and wrong mac adress rssi publishing * add esp32 to CI * correct esp32 ide retrieving * correcting paths * CI: correct architecture * libraries update (irremote) and overwrite ble library files
56 lines
2.0 KiB
C
56 lines
2.0 KiB
C
/*
|
|
OpenMQTTGateway - ESP8266 or Arduino program for home automation
|
|
|
|
Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker
|
|
Send and receiving command by MQTT
|
|
|
|
This files enables to set your parameter for the bluetooth low energy gateway (beacons detection)
|
|
|
|
Copyright: (c)Florian ROBERT
|
|
|
|
This file is part of OpenMQTTGateway.
|
|
|
|
OpenMQTTGateway is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
OpenMQTTGateway is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
/*----------------------BT topics & parameters-------------------------*/
|
|
#define subjectBTtoMQTT "home/BTtoMQTT/"
|
|
#define TimeBtw_Read 20000 //define the time between 2 scans
|
|
#define Scan_duration 10 //define the time for a scan
|
|
#define HM-10
|
|
//#define HM-11 // uncomment this line if you use HM-11 and comment the line above
|
|
#define ZgatewayBT_v6xx // comment if you don't have a firmware version of HM10/11 >= v601
|
|
#define delimiter "4f4b2b444953413a"
|
|
#define delimiter_length 16
|
|
|
|
struct decompose
|
|
{
|
|
char subject[4];
|
|
int start;
|
|
int len;
|
|
boolean reverse;
|
|
char extract[60];
|
|
};
|
|
|
|
/*-------------------PIN DEFINITIONS----------------------*/
|
|
#ifdef ESP8266
|
|
#define BT_RX 13 //D7 ESP8266 RX connect HM-10 or 11 TX
|
|
#define BT_TX 12 //D6 ESP8266 TX connect HM-10 or 11 RX
|
|
#elif defined(ESP32)
|
|
#define BT_RX 18 // not tested
|
|
#define BT_TX 19 // not tested
|
|
#else
|
|
#define BT_RX 5 //arduino RX connect HM-10 or 11 TX
|
|
#define BT_TX 6 //arduino TX connect HM-10 or 11 RX
|
|
#endif
|