Florian
b4003d4ea1
Manual control with a button press triggered the relay but 2 times (when pressing and releasing), fixing this. Check that we have two consecutive readings of temperature above the threshold to trigger the actuator to OFF And remove it by default to the shelly, as I see unjustified jumps of temperature above 80C.
68 lines
2.8 KiB
C
68 lines
2.8 KiB
C
/*
|
|
OpenMQTTGateway - ESP8266 or Arduino program for home automation
|
|
|
|
Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker
|
|
Send and receiving command by MQTT
|
|
|
|
This files enables to set your parameter for the ON OFF actuator
|
|
|
|
Copyright: (c)Florian ROBERT
|
|
|
|
This file is part of OpenMQTTGateway.
|
|
|
|
OpenMQTTGateway is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
OpenMQTTGateway is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
#ifndef config_ONOFF_h
|
|
#define config_ONOFF_h
|
|
|
|
extern void setupONOFF();
|
|
extern void MQTTtoONOFF(char* topicOri, char* datacallback);
|
|
extern void MQTTtoONOFF(char* topicOri, JsonObject& RFdata);
|
|
/*----------------------------USER PARAMETERS-----------------------------*/
|
|
/*-------------DEFINE YOUR MQTT PARAMETERS BELOW----------------*/
|
|
#define subjectMQTTtoONOFF "/commands/MQTTtoONOFF"
|
|
#define subjectGTWONOFFtoMQTT "/ONOFFtoMQTT"
|
|
|
|
#define ONKey "setON"
|
|
#define OFFKey "setOFF"
|
|
#ifndef ACTUATOR_ON
|
|
# define ACTUATOR_ON LOW // LOW or HIGH, set to the output level of the GPIO pin to turn the actuator on.
|
|
#endif
|
|
//# define ACTUATOR_ONOFF_DEFAULT !ACTUATOR_ON // ACTUATOR_ON or !ACTUATOR_ON, set to the state desired on reset.
|
|
#ifndef ACTUATOR_TRIGGER
|
|
# define ACTUATOR_TRIGGER false // false or true, enable to control an actuator directly from the board switch (default behavior if true), or by button if ACTUATOR_BUTTON_TRIGGER_LEVEL is also defined
|
|
#endif
|
|
#ifndef ACTUATOR_BUTTON_TRIGGER_LEVEL
|
|
//# define ACTUATOR_BUTTON_TRIGGER_LEVEL LOW // 0 or 1, set to the level which to detect a button press to change the actuator state.
|
|
#endif
|
|
#ifndef MAX_TEMP_ACTUATOR
|
|
//# define MAX_TEMP_ACTUATOR 70 // Temperature that will trigger the relay to go OFF
|
|
#endif
|
|
#ifndef TimeBetweenReadingIntTemp
|
|
# define TimeBetweenReadingIntTemp 5000 // Time interval between internal temp measurement to switch off the relay if MAX_TEMP_ACTUATOR is reached
|
|
#endif
|
|
/*-------------------PIN DEFINITIONS----------------------*/
|
|
// default pin, if not set into the MQTT json
|
|
#ifndef ACTUATOR_ONOFF_GPIO
|
|
# ifdef ESP8266
|
|
# define ACTUATOR_ONOFF_GPIO 15 //12 for sonoff basic relay
|
|
# elif ESP32
|
|
# define ACTUATOR_ONOFF_GPIO 15
|
|
# else
|
|
# define ACTUATOR_ONOFF_GPIO 13
|
|
# endif
|
|
#endif
|
|
|
|
#endif
|