Florian
441ab1c0b7
* some minor correction after coadcy checks * Put serial communication speed as a parameter in user_config.h * complete gateway file receiving ok sending ko #32 * add rfm69 to CI * change receiver key and minor improvments #32 now ok on receiving and sending with RFM69 * add schema and tested pinout for RFM69/RF/IR wiring #32 * RFM69 library add * Implement newremoteswitchlibrary for KlikAanKlikUit / ClickOnClickOff protocol #3 * add dependency for CI and link to the library * compilation error for arduino correction * Sketch size decrease * remove nano from CI * Divide user_config into one file per gateway/sensor for lisibility
69 lines
2.7 KiB
C
69 lines
2.7 KiB
C
/*
|
|
OpenMQTTGateway - ESP8266 or Arduino program for home automation
|
|
|
|
Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker
|
|
Send and receiving command by MQTT
|
|
|
|
This files enables to set your parameter for the radiofrequency gateways (ZgatewayRF and ZgatewayRF2) with RCswitch and newremoteswitch library
|
|
|
|
Copyright: (c)Florian ROBERT
|
|
|
|
This file is part of OpenMQTTGateway.
|
|
|
|
OpenMQTTGateway is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
OpenMQTTGateway is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
|
|
/*----------------------RFM69 topics & parameters -------------------------*/
|
|
#define subjectRFM69toMQTT "home/RFM69toMQTT"
|
|
#define subjectRFM69toMQTTrssi "home/RFM69toMQTT/rssi"
|
|
#define subjectRFM69toMQTTsender "home/RFM69toMQTT/sender"
|
|
#define subjectMQTTtoRFM69 "home/commands/MQTTtoRFM69"
|
|
#define RFM69receiverKey "RCV_" // receiver id will be defined if a subject contains RFM69receiverKey followed by a value of 3 digits
|
|
#define subjectGTWRFM69toMQTT "home/RFM69toMQTT"
|
|
#define defaultRFM69ReceiverId 99
|
|
|
|
// Default values
|
|
const char PROGMEM ENCRYPTKEY[] = "sampleEncryptKey";
|
|
const char PROGMEM MDNS_NAME[] = "rfm69gw1";
|
|
const char PROGMEM MQTT_BROKER[] = "raspi2";
|
|
const char PROGMEM RFM69AP_NAME[] = "RFM69-AP";
|
|
#define NETWORKID 200 //the same on all nodes that talk to each other
|
|
#define NODEID 10
|
|
|
|
//Match frequency to the hardware version of the radio
|
|
#define FREQUENCY RF69_433MHZ
|
|
//#define FREQUENCY RF69_868MHZ
|
|
//#define FREQUENCY RF69_915MHZ
|
|
#define IS_RFM69HCW true // set to 'true' if you are using an RFM69HCW module
|
|
#define POWER_LEVEL 31
|
|
|
|
/*-------------------PIN DEFINITIONS----------------------*/
|
|
|
|
#ifdef RFM69_Wiring // Without Support for I2C Modules and HM10 or 11
|
|
|
|
#ifdef ESP8266
|
|
#define RFM69_CS D1 // GPIO5/HCS/D1
|
|
#define RFM69_IRQ D8 // GPIO15/D8
|
|
#define RFM69_IRQN digitalPinToInterrupt(RFM69_IRQ)
|
|
#define RFM69_RST D4 // GPIO02/D4
|
|
#else
|
|
//RFM69 not tested with arduino
|
|
#define RFM69_CS 10
|
|
#define RFM69_IRQ 2
|
|
#define RFM69_IRQN digitalPinToInterrupt(RFM69_IRQ)
|
|
#define RFM69_RST 9
|
|
#endif
|
|
#endif
|
|
|