h2zero
5e11690b69
This will provide the expected funtionality for the reset trigger when the button is pressed for more than 10 seconds. Also allows the same pin to be used as an actuator/relay trigger if pressed for less than 10 seconds.
62 lines
2.3 KiB
C
62 lines
2.3 KiB
C
/*
|
|
OpenMQTTGateway - ESP8266 or Arduino program for home automation
|
|
|
|
Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker
|
|
Send and receiving command by MQTT
|
|
|
|
This files enables to set your parameter for the ON OFF actuator
|
|
|
|
Copyright: (c)Florian ROBERT
|
|
|
|
This file is part of OpenMQTTGateway.
|
|
|
|
OpenMQTTGateway is free software: you can redistribute it and/or modify
|
|
it under the terms of the GNU General Public License as published by
|
|
the Free Software Foundation, either version 3 of the License, or
|
|
(at your option) any later version.
|
|
|
|
OpenMQTTGateway is distributed in the hope that it will be useful,
|
|
but WITHOUT ANY WARRANTY; without even the implied warranty of
|
|
MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
|
|
GNU General Public License for more details.
|
|
|
|
You should have received a copy of the GNU General Public License
|
|
along with this program. If not, see <http://www.gnu.org/licenses/>.
|
|
*/
|
|
#ifndef config_ONOFF_h
|
|
#define config_ONOFF_h
|
|
|
|
extern void setupONOFF();
|
|
extern void MQTTtoONOFF(char* topicOri, char* datacallback);
|
|
extern void MQTTtoONOFF(char* topicOri, JsonObject& RFdata);
|
|
/*----------------------------USER PARAMETERS-----------------------------*/
|
|
/*-------------DEFINE YOUR MQTT PARAMETERS BELOW----------------*/
|
|
#define subjectMQTTtoONOFF "/commands/MQTTtoONOFF"
|
|
#define subjectGTWONOFFtoMQTT "/ONOFFtoMQTT"
|
|
|
|
#define ONKey "setON"
|
|
#define OFFKey "setOFF"
|
|
#ifndef ACTUATOR_ON
|
|
# define ACTUATOR_ON LOW // 0 or 1, set to the output level of the gpio pin to turn the actuator on.
|
|
#endif
|
|
#ifndef ACTUATOR_ONOFF_DEFAULT
|
|
# define ACTUATOR_ONOFF_DEFAULT !ACTUATOR_ON // ACTUATOR_ON or !ACTUATOR_ON, set to the state desired on reset.
|
|
#endif
|
|
#ifndef ACTUATOR_BUTTON_TRIGGER_LEVEL
|
|
# define ACTUATOR_BUTTON_TRIGGER_LEVEL LOW // 0 or 1, set to the sensing level which to detect a button press to change the actuator state.
|
|
#endif
|
|
|
|
/*-------------------PIN DEFINITIONS----------------------*/
|
|
// default pin, if not set into the MQTT json
|
|
#ifndef ACTUATOR_ONOFF_GPIO
|
|
# ifdef ESP8266
|
|
# define ACTUATOR_ONOFF_GPIO 15 //12 for sonoff basic relay
|
|
# elif ESP32
|
|
# define ACTUATOR_ONOFF_GPIO 15
|
|
# else
|
|
# define ACTUATOR_ONOFF_GPIO 13
|
|
# endif
|
|
#endif
|
|
|
|
#endif
|