/* OpenMQTTGateway - ESP8266 or Arduino program for home automation Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker Send and receiving command by MQTT This program enables to: - receive MQTT data from a topic and send RF 433Mhz signal corresponding to the received MQTT data - publish MQTT data to a different topic related to received 433Mhz signal - receive MQTT data from a topic and send IR signal corresponding to the received MQTT data - publish MQTT data to a different topic related to received IR signal - publish MQTT data to a different topic related to BLE devices rssi signal Copyright: (c)Florian ROBERT This file is part of OpenMQTTGateway. OpenMQTTGateway is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. OpenMQTTGateway is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see . */ /*-------------------VERSION----------------------*/ #define OMG_VERSION "0.9beta" /*-------------CONFIGURE WIFIMANAGER-------------*/ /* * The following parameters are set during the WifiManager setup process: * - wifi_ssid * - wifi_password * - mqtt_user * - mqtt_pass * - mqtt_server * - mqtt_port * * To completely disable WifiManager, define ESPWifiManualSetup. * If you do so, please don't forget to set these variables before compiling * * Otherwise you can provide these credentials on the web interface after connecting * to the access point with your password (SSID: WifiManager_ssid, password: WifiManager_password) */ #if defined(ESP8266) // for nodemcu, weemos and esp8266 //#define ESPWifiManualSetup true //uncomment you don't want to use wifimanager for your credential settings on ESP #endif #define WifiManager_password "your_password" //this is going to be the WPA2-PSK password for the initial setup access point #define WifiManager_ssid "OpenMQTTGateway" //this is the network name of the initial setup access point #define WifiManager_ConfigPortalTimeOut 120 /*-------------DEFINE YOUR MQTT PARAMETERS BELOW----------------*/ //MQTT Parameters definition //#define mqtt_server_name "www.mqtt_broker.com" // instead of defining the server by its IP you can define it by its name, uncomment this line and set the correct MQTT server host name char mqtt_user[20] = "your_username"; // not compulsory only if your broker needs authentication char mqtt_pass[30] = "your_password"; // not compulsory only if your broker needs authentication char mqtt_server[40] = "192.168.1.17"; char mqtt_port[6] = "1883"; #define Gateway_Name "OpenMQTTGateway" #define Base_Topic "home/" #define version_Topic Base_Topic Gateway_Name "/version" #define will_Topic Base_Topic Gateway_Name "/LWT" #define will_QoS 0 #define will_Retain true #define will_Message "Offline" #define Gateway_AnnouncementMsg "Online" /*-------------DEFINE YOUR NETWORK PARAMETERS BELOW----------------*/ //#define MDNS_SD //uncomment if you want to use mdns for discovering automatically your ip server, please note that MDNS with ESP32 can cause the BLE to not work #define maxMQTTretry 4 //maximum MQTT connection attempts before going to wifi setup //set minimum quality of signal so it ignores AP's under that quality #define MinimumWifiSignalQuality 8 // Update these with values suitable for your network. #if defined(ESP32) || defined(ESPWifiManualSetup) // for nodemcu, weemos and esp8266 #define wifi_ssid "wifi ssid" #define wifi_password "wifi password" #else // for arduino + W5100 const byte mac[] = { 0xDE, 0xED, 0xBA, 0xFE, 0x54, 0x95 }; //W5100 ethernet shield mac adress #endif // these values are only used if no dhcp configuration is available const byte ip[] = { 192, 168, 1, 99 }; //ip adress // Advanced network config (optional) if you want to use these parameters uncomment line 158, 172 and comment line 171 of OpenMQTTGateway.ino const byte gateway[] = { 192, 168, 1, 1 }; //ip adress const byte Dns[] = { 192, 168, 1, 1 }; //ip adress const byte subnet[] = { 255, 255, 255, 0 }; //ip adress /*-------------DEFINE YOUR OTA PARAMETERS BELOW----------------*/ #define ota_hostname "OTAHOSTNAME" #define ota_password "OTAPASSWORD" #define ota_port 8266 /*-------------DEFINE PINs FOR STATUS LEDs----------------*/ #define led_receive 40 #define led_send 42 #define led_error 44 // VCC ------------D|-----------/\/\/\/\ ----------------- Arduino PIN // LED Resistor 270-510R /*-------------DEFINE THE MODULES YOU WANT BELOW----------------*/ //Addons and module management, comment the Z line and the config file if you don't use #if defined(ESP8266) // for nodemcu, weemos, esp8266, and Arduino mega #define ZgatewayRF "RF" //#define ZgatewayLORA "LORA" (not tested yet) #define ZgatewayRF315 "RF315" #define ZgatewaySRFB "SRFB" #define ZgatewayRF2 "RF2" #define ZgatewayIR "IR" #define ZgatewayBT "BT" #define Zgateway2G "2G" #define ZgatewayPilight "Pilight" #define ZactuatorONOFF "ONOFF" #define ZsensorINA226 "INA226" #define ZsensorHCSR501 "HCSR501" #define ZsensorADC "ADC" #define ZsensorBH1750 "BH1750" #define ZsensorBME280 "BME280" #define ZsensorTSL2561 "TSL2561" #define ZsensorDHT "DHT"// If you uncomment this you can't use I2C due to the fact that I2C use also D1 #define ZgatewayRFM69 "RFM69"// If you uncomment this you can't use RF and BT due to the fact that RF use also D8 and BT use also D6/D7 #define ZsensorGPIOInput "GPIOInput" #define ZsensorGPIOKeyCode "GPIOKeyCode" #define ZmqttDiscovery "HADiscovery"//ESP8266, Arduino, EPS32, Sonoff RF Bridge #define jsonPublishing true #define simplePublishing true #elif ESP32 #define ZgatewayRF "RF" #define ZgatewayLORA "LORA" #define ZgatewayRF "RF315" #define ZgatewayRF2 "RF2" //#define Zgateway2G (not tested yet) #define ZgatewayIR "IR" #define ZgatewayBT "BT" #define ZactuatorONOFF "ONOFF" #define ZsensorINA226 "INA226" //ESP8266, Arduino, ESP32 #define ZsensorHCSR501 "HCSR501" //ESP8266, Arduino, ESP32, Sonoff RF Bridge #define ZsensorADC "ADC" //ESP8266, Arduino, ESP32 #define ZsensorBH1750 "BH1750" //ESP8266, Arduino, ESP32 #define ZsensorBME280 "BME280" //ESP8266, Arduino, ESP32 #define ZsensorTSL2561 "TSL2561" #define ZsensorDHT "DHT" #define ZgatewayRFM69 "RFM69" #define ZsensorGPIOInput "GPIOInput" #define ZsensorGPIOKeyCode "GPIOKeyCode" #define ZmqttDiscovery "HADiscovery"//ESP8266, Arduino, EPS32, Sonoff RF Bridge #define jsonPublishing true #define simplePublishing true #elif defined(__AVR_ATmega1280__) #define ZgatewayRF "RF" //#define ZgatewayLORA "LORA" (not tested yet) #define ZgatewayRF315 "RF315" #define ZgatewaySRFB "SRFB" #define ZgatewayRF2 "RF2" #define ZgatewayIR "IR" #define ZgatewayBT "BT" #define Zgateway2G "2G" //#define ZgatewayPilight "Pilight" #define ZactuatorONOFF "ONOFF" #define ZsensorINA226 "INA226" #define ZsensorHCSR501 "HCSR501" #define ZsensorADC "ADC" #define ZsensorBH1750 "BH1750" #define ZsensorBME280 "BME280" #define ZsensorTSL2561 "TSL2561" #define ZsensorDHT "DHT"// If you uncomment this you can't use I2C due to the fact that I2C use also D1 #define ZgatewayRFM69 "RFM69"// If you uncomment this you can't use RF and BT due to the fact that RF use also D8 and BT use also D6/D7 #define ZsensorGPIOInput "GPIOInput" #define ZsensorGPIOKeyCode "GPIOKeyCode" #define ZmqttDiscovery "HADiscovery"//ESP8266, Arduino, EPS32, Sonoff RF Bridge #define jsonPublishing true #define simplePublishing true #else // for arduino Uno #define ZgatewayRF "RF" //#define ZgatewayLORA "LORA" (not tested yet) //#define Zgateway2G (not tested yet) //#define ZgatewayRF2 // too big for UNO //#define ZgatewayIR //#define ZgatewayBT //#define ZactuatorONOFF //#define ZsensorINA226 //#define ZsensorDHT //#define ZsensorBH1750 //#define ZsensorBME280 //#define ZsensorHCSR501 //#define ZsensorADC //#define ZgatewayRFM69 //not tested //#define ZsensorGPIOInput //not tested //#define ZsensorGPIOKeyCode "GPIOKeyCode" //not tested #define jsonPublishing true //#define simplePublishing true #endif /*----------------------------OTHER PARAMETERS-----------------------------*/ #ifdef ZgatewaySRFB #define SERIAL_BAUD 19200 #else #define SERIAL_BAUD 115200 #endif /*-------------------CHANGING THEM IS NOT COMPULSORY-----------------------*/ /*--------------MQTT general topics-----------------*/ // global MQTT subject listened by the gateway to execute commands (send RF, IR or others) #define subjectMQTTtoX Base_Topic Gateway_Name "/commands/#" #define subjectMultiGTWKey "toMQTT" #define subjectGTWSendKey "MQTTto" #define valueAsASubject true //variables to avoid duplicates #define time_avoid_duplicate 3000 // if you want to avoid duplicate mqtt message received set this to > 0, the value is the time in milliseconds during which we don't publish duplicates #ifdef ESP32 //#define multiCore //uncomment to use multicore function of ESP32 for BLE #endif #define JSON_MSG_BUFFER 256 // Json message max buffer size, don't put 1024 or higher it is causing unexpected behaviour on ESP8266 #define TimeBetweenReadingSYS 30000 // time between system readings (like memory) #define subjectSYStoMQTT Base_Topic Gateway_Name "/SYStoMQTT" /*-------------------ACTIVATE TRACES----------------------*/ #define TRACE 0 // 0= trace off 1 = trace on