# Integrate Home Assistant Home Assistant provide the [MQTT integration](https://www.home-assistant.io/integrations/mqtt/) and through this integration it is possible to exploit and manage the messages published by OpenMQTTGateway. Once this integration on home assistant is configured with the same MQTT broker, it is possible to create devices manually or through the autodiscovery function. ## Automatic integration with Auto discovery From Home Assistant site > The discovery of MQTT devices will enable one to use MQTT devices with only minimal configuration effort on the side of Home Assistant. The configuration is done on the device itself and the topic used by the device. On OpenMQTTGateway the Home Assistant discovery is enabled by default on all binaries and platformio configurations. Here are a few tips for activating discovery on Home Assistant, but for detailed configuration please refer to the Home Assistant website. Enable discovery on your MQTT integration in HASS (activated per default). ![Home Assistant Auto Discovery](../img/OpenMQTTGateway-Configuration-Home-Assistant-Discovery-Integration.png) The gateway will need an MQTT username and password, you have to create a new user (recommended) into Home Assistant->Configuration->Users (available in admin mode) or use an existing username/pwd combination (not recommended). This user doesn't need to be an administrator. ![Home Assistant Auto Discovery](../img/OpenMQTTGateway-Configuration-Home-Assistant.png) ::: warning Note The max size of the username and password is 64 characters. ::: OMG will use the auto discovery functionality of home assistant to create gateway and sensors into your HASS instance automatically. ![Home Assistant Auto Discovery](../img/OpenMQTTGateway_auto_discovery_Gateway_Home_Assistant.gif) ![Home Assistant Auto Discovery](../img/OpenMQTTGateway_auto_discovery_BLE_Sensor_Home_Assistant.gif) ![Home Assistant Auto Discovery](../img/OpenMQTTGateway_Home_Assistant_MQTT_discovery.png) ::: tip INFO The Bluetooth and the RTL_433 gateway will automatically create devices and entities, the RF gateway will create DeviceTrigger. The OpenMQTTGateway will also be available as a device to monitor its parameters and control it. The sensors (DHT for example) and actuators (relays) are attached to the gateway. On first and subsequent startups, auto discovery will start. If you want to prevent this from happening, be sure to manually turn off auto discovery, either by using the UI in Home Assistant, or by publishing to the home//commands/MQTTtoSYS/config topic. 30 minutes after its activation the auto discovery will be automatically deactivated, you can reactivate it from the gateway controls. Some devices may require a button push or motion/contact event to trigger a message and generate the auto discovery. ::: ### RTL_433 auto discovery specificity Even if the RTL_433 gateway will create automatically the devices and entities, you may lose the link to them when you change the batteries. This is proper to the RF devices. In this case new device and entities will be created. You may bypass this by creating entities through manual configuration that filter following the device model and other parameters and don't take into account the id. Example: ```yaml mqtt: sensor: - state_topic: "+/+/RTL_433toMQTT/WS2032/+" ``` instead of ```yaml mqtt: sensor: - state_topic: "+/+/RTL_433toMQTT/WS2032/47998" ``` Note also that the sensor may leverage channels, types or subtypes, they can be used in the filtering Example: In the example below 9 is the `subtype` and 1 is the `channel` ```yaml mqtt: sensor: - state_topic: "+/+/RTL_433toMQTT/Prologue-TH/9/1/+" ``` instead of ```yaml mqtt: sensor: - state_topic: "+/+/RTL_433toMQTT/Prologue-TH/9/1/215" ``` Alternatively the rssi signal could be used also. ### RF (RCSwitch based gateway) Auto discovery specificity With OpenMQTTGateway [configured to receive RF signals](../setitup/rf.html) messages are transmitted accordingly. As indicated in the [RCSwitch based gateway](../use/rf.html#rcswitch-based-gateway), it is possible to receive a pulse each time the sensor detects a signal. With auto-discovery enabled, you can configure two types of entities in Home Assistant to handle RF signals: 1. An [MQTT Device Trigger](https://www.home-assistant.io/integrations/device_trigger.mqtt/) which allows actions to be triggered when a specific RF signal is received. 2. An [MQTT Sensor](https://www.home-assistant.io/integrations/sensor.mqtt/) which stores the received RF data as a sensor value. Below are some examples of both configurations. #### Example A - RF as MQTT Device Trigger If the following parameters are enabled in OpenMQTTGateway: - ZgatewayRF="RF" - valueAsATopic=true - HADiscovery=true - RF_on_HAS_as_DeviceTrigger=true - RF_on_HAS_as_MQTTSensor=false Then, each time an RF signal is received by OpenMQTTGateway, two messages are sent to the MQTT broker: 1. A device trigger announcement (used by Home Assistant to recognize the trigger). 2. The RF signal data on the corresponding MQTT topic. ``` ... N: [ OMG->MQTT ] topic: homeassistant/device_automation/246F287AF0C4/15524904/config msg: {"automation_type":"trigger","platform ":"device_automation","type":"Received","subtype":"RF-15524904","device":{"configuration_url":"http://192.168.2.150/","connections":[["mac","246F287AF0C4"]],"identifiers":["246F287AF0C4"],"mf":"OMG_community","mdl":"[\"WebUI\",\"RF\"]","name":"OMG_DEVELOPMENT","sw":"1.8.0-o"},"value_template":"{{trigger.value.raw}}","topic":"home/OMG_DEVELOPMENT/433toMQTT/15524904"} T: Dequeue JSON N: [ OMG->MQTT ] topic: home/OMG_DEVELOPMENT/433toMQTT/15524904 msg: {"value":15524904,"protocol":1,"length":24,"delay":368,"tre_state":"-","binary":"111011001110010000101000","raw":"11427,1042,407,1039,417,1027,430,302,1148,1019,438,1015,440,295,1152,301,1153,1014,442,1012,441,1008,445,291,1160,293,1158,1011,444,292,1156,296,1157,296,1157,298,1154,1011,442,295,1153,1013,443,293,1157,295,1154,300"} ... ``` These messages allow Home Assistant to recognize and integrate the RF signal as a device trigger. ![MQTTExplorer Show Topic](../img/HASS-RF-DeviceTrigger.png) *Example of a detected RF device trigger in Home Assistant: Green shows the real message, Yellow shows the device trigger configuration* Once this process is completed, Home Assistant detects a new trigger associated with the OpenMQTTGateway device and linked to the received RF signal value. This means that Home Assistant can now react to the received RF signal as an automation trigger. Example of a detected RF trigger in Home Assistant: ![MQTTExplorer Show Topic](../img/HASS-RF-Trigger-example.png) *Example of a detected RF trigger in Home Assistant* #### Example B - RF As MQTT Sensor If the following parameters are enabled in OpenMQTTGateway: - ZgatewayRF="RF" - HADiscovery=true - RF_on_HAS_as_DeviceTrigger=false - RF_on_HAS_as_MQTTSensor=true During any discovery round, a SYS message is sent, setting the MQTT Sensor as a sensor of the OpenMQTTGateway device. ``` ... N: [ OMG->MQTT ] topic: homeassistant/sensor/246F287AF0C4-gatewayRF/config msg: {"stat_t":"home/OMG_DEVELOPMENT/433toMQTT/#","avty_t":"home/OMG_DEVELOPMENT/LWT","name":"gatewayRF","uniq_id":"246F287AF0C4-gatewayRF","val_tpl":"{{ value_json.value | is_defined }}","pl_avail":"online","pl_not_avail":"offline","device":{"ids":["246F287AF0C4"],"name":"OMG_DEVELOPMENT","mdl":"[\"WebUI\",\"RF\"]","mf":"OMG_community","cu":"http://192.168.2.150/","sw":"1.8.0-o"}} T: Dequeue JSON ``` Then, each time an RF signal is received by OpenMQTTGateway, the content of messages are sent to the MQTT broker on classic topic: ``` T: Dequeue JSON N: [ OMG->MQTT ] topic: home/OMG_DEVELOPMENT/433toMQTT/15524904 msg: {"value":15524904,"protocol":1,"length":24,"delay":368,"tre_state":"-","binary":"111011001110010000101000","raw":"11404,1045,414,1034,424,1024,430,305,1146,1022,431,1019,436,299,1150,304,1145,1021,432,1017,438,1013,441,295,1156,299,1149,1018,436,300,1149,304,1146,307,1143,310,1141,1025,430,306,1143,1021,432,305,1145,310,1140,309"} ``` These messages enable Home Assistant to recognize and integrate the RF signal as a sensor. ![MQTTExplorer Show Topic](../img/HASS-RF-MQTTSensor.png) *Example of a detected RF sensor in Home Assistant: Yellow the configuration of sensor, Green the real message* Once this process is completed, Home Assistant detects a device with the new sensor and linked to the received RF signal value. This means that Home Assistant can now react to the received RF signal as an sensor event. Example of a detected RF trigger in Home Assistant: ![MQTTExplorer Show Topic](../img/HASS-RF-Sensor-example.png) *Example of a detected RF sensor in Home Assistant: Yellow the real message* ## Manual integration If you prefer not to use MQTT auto-discovery, you can manually configure Home Assistant to manage MQTT topics. This approach gives you full control over the structure and behavior of your MQTT entities. Below are some examples of how to define your devices, sensors, and switches manually using YAML configuration. From @123, @finity, @denniz03, @jrockstad, @anarchking, @dkluivingh, @Odyno ### Pir Sensor This is an example of how to configure a PIR (Passive Infrared) sensor in Home Assistant using MQTT. ![Pir Sensor](../img/digoo-pir-DG-HOSA.png) The configuration below sets up a binary sensor that detects motion and sends the state to Home Assistant. ```yaml mqtt: binary_sensor: - unique_id: pir.15484294 name: "Pir.Mansarda" device_class: motion state_topic: "home/+/433toMQTT/15484294" value_template: "{{ value_json.value }}" payload_on: "15484294" off_delay: 3 ``` ### Door sensor ```yaml mqtt: binary_sensor: - name: "test" state_topic: "home/OpenMQTTGateway/433toMQTT" value_template: >- {% if value_json.value == '7821834' %} {{'ON'}} {% elif value_json.value == '7821838' %} {{'OFF'}} {% else %} {{states('binary_sensor.test') | upper}} {% endif %} qos: 0 device_class: opening ``` ```yaml mqtt: binary_sensor: - name: doorbell state_topic: 'home/OpenMQTTGateway/SRFBtoMQTT' #value_template: "{{ value_json.raw }}" value_template: >- {% if value_json.value == '14163857' %} {{'ON'}} {% else %} {{states('binary_sensor.doorbell') | upper}} {% endif %} off_delay: 30 device_class: 'sound' - name: light_back_sensor state_topic: 'home/OpenMQTTGateway/SRFBtoMQTT' #value_template: '{{ value_jason.value }}' value_template: >- {% if value_json.value == '1213858' %} {{'ON'}} {% else %} {{states('binary_sensor.light_back_sensor') | upper}} {% endif %} off_delay: 5 - name: rf_outlet_sensor state_topic: 'home/OpenMQTTGateway/SRFBtoMQTT' value_template: >- {% if value_json.value == '16766303' %} {{'ON'}} {% else %} {{states('binary_sensor.rf_outlet_sensor') | upper}} {% endif %} ``` ### Motion sensor ```yaml mqtt: binary_sensor: - name: "Bewegung_Schlafzimmer" #device_class: motion state_topic: "home/OpenMQTTGateway1/HCSR501toMQTT" value_template: '{{ value_json["presence"] }}' payload_on: "true" payload_off: "false" ``` ### Switches ```yaml #switches mqtt: switch: - name: Plug1 state_topic: "home/OpenMQTTGateway/SRFBtoMQTT" command_topic: "home/OpenMQTTGateway/commands/MQTTtoSRFB" value_template: "{{ value_json.value }}" payload_on: '{"value":4546575}' payload_off: '{"value":4546572}' state_on: 4546575 state_off: 4546572 qos: "0" retain: true ``` ### RF gateway mode - Pilight, RF, kaku insert an include statement in HA configuration.yaml ```bash grep homed ./configuration.yaml mqtt: !include homed-mqtt.yaml ``` In the example, the included file is homed-mqtt.yaml. It provides an mqtt select entity with the ability to show and also change via dropdown - the desired mode of the RF receiver gateway. In the homed-mqtt.yaml snippet, the device section (as it is optional) is ommited, ```yaml select: - name: 'RF: Mode receive' unique_id: espdevcho-rf-mode #platform: mqtt availability_topic: home/espdevcho/LWT # espdevcho is a particular name of the gateway, instead of the default OpenMQTTGateway payload_available: online payload_not_available: offline options: - "Pilight" - "RF classic" - "RF2 kaku" state_topic: home/espdevcho/RFtoMQTT # espdevcho is a particular name of the gateway, instead of the default OpenMQTTGateway value_template: > {% if value_json.active == 1 %} Pilight {% elif value_json.active == 2 %} RF classic {% elif value_json.active == 4 %} RF2 kaku {% endif %} #unit_of_measurement: s command_topic: home/espdevcho/commands/MQTTtoRF/config # espdevcho is a particular name of the gateway, instead of the default OpenMQTTGateway command_template: > {% set value_map = { "Pilight": 1, "RF classic": 2, "RF2 kaku": 4, } %} {"active":{{ value_map[value] }}} device: configuration_url: http://192.168.1.11/ # device section is optional. It is almost ommited in this example. Values here will update the corresponding device, if it already exist ``` ### Mijia Thermometer BLE ```yaml mqtt: sensor: - name: "mijia_thermometer_temperature" state_topic: 'home/OpenMQTTGateway/BTtoMQTT/AAAAAAAAAAAA' # MQTT topic, check MQTT messages; replace AA... with id (BLE MAC) of your device unit_of_measurement: '°C' value_template: '{{ value_json.tem | is_defined }}' expire_after: 21600 # 6 hours force_update: true - name: "mijia_thermometer_humidity" state_topic: 'home/OpenMQTTGateway/BTtoMQTT/AAAAAAAAAAAA' unit_of_measurement: '%' value_template: '{{ value_json.hum | is_defined }}' expire_after: 21600 # 6 hours force_update: true - name: "mijia_thermometer_battery" state_topic: 'home/OpenMQTTGateway/BTtoMQTT/AAAAAAAAAAAA' unit_of_measurement: '%' value_template: '{{ value_json.batt | is_defined }}' expire_after: 21600 # 6 hours force_update: true ``` ### Xiaomi Mi Scale V2 BLE (XMTZC05HM) ```yaml mqtt: sensor: - name: "Weight" state_topic: "home/OpenMQTTGateway/BTtoMQTT/AAAAAAAAAAAA" # replace your MQTT topic here value_template: '{{ value_json["weight"] }}' unit_of_measurement: "kg" icon: mdi:weight-kilogram - name: "Impedance" state_topic: "home/OpenMQTTGateway/BTtoMQTT/AAAAAAAAAAAA" # replace your MQTT topic here also value_template: '{{ value_json["impedance"] }}' unit_of_measurement: "Ohm" icon: mdi:omega template: sensor: - name: body_mass_index: friendly_name: 'Body Mass Index' value_template: >- {% set HEIGHT = (1.76)|float %} # replace your height in meters {% set WEIGHT = states('sensor.xmtzc05hm_weight')|float %} {{- (WEIGHT/(HEIGHT*HEIGHT))|float|round(1) -}} icon_template: > {{ 'mdi:human' }} ``` ### MQTT Room Presence For the publication into the presence topic the following needs to be activated - [here is the command](../use/ble.html#setting-if-the-gateway-publish-into-home-assistant-home-presence-topic-default-false-available-with-ha-discovery) ```yaml sensor: - platform: mqtt_room device_id: XX:XX:XX:XX:XX:XX #Mac Address of device wanting to track name: you_are_in # home assistant will show a sensor named (you are in) with its value being the name you gave the gateway state_topic: "home/presence" #timeout: #away_timeout: ``` ### Temperature sensor ```yaml mqtt: sensor: - name: outdoor temp state_topic: "home/OpenMQTTGateway/433toMQTT" unit_of_measurement: '°C' value_template: > {% if value_json is defined and value_json.sensor == 125 %} {{ value_json.tempc }} {% else %} {{ states('sensor.outdoor_temp') }} {% endif %} ```