/* OpenMQTTGateway - ESP8266 or Arduino program for home automation Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker Send and receiving command by MQTT This program enables to: - receive MQTT data from a topic and send signals corresponding to the received MQTT data - publish MQTT data to a different topic related to received signals Copyright: (c)Florian ROBERT This file is part of OpenMQTTGateway. OpenMQTTGateway is free software: you can redistribute it and/or modify it under the terms of the GNU General Public License as published by the Free Software Foundation, either version 3 of the License, or (at your option) any later version. OpenMQTTGateway is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for more details. You should have received a copy of the GNU General Public License along with this program. If not, see . */ /*-------------------VERSION----------------------*/ #define OMG_VERSION "0.9beta" /*-------------CONFIGURE WIFIMANAGER-------------(only ESP8266 & SONOFF RFBridge)*/ /* * The following parameters are set during the WifiManager setup process: * - wifi_ssid * - wifi_password * - mqtt_user * - mqtt_pass * - mqtt_server * - mqtt_port * * To completely disable WifiManager, define ESPWifiManualSetup. * If you do so, please don't forget to set these variables before compiling * * Otherwise you can provide these credentials on the web interface after connecting * to the access point with your password (SSID: WifiManager_ssid, password: WifiManager_password) */ /*-------------DEFINE YOUR NETWORK PARAMETERS BELOW----------------*/ #if defined(ESP8266) // for nodemcu, weemos and esp8266 //#define ESPWifiManualSetup true //uncomment you don't want to use wifimanager for your credential settings on ESP #endif #if defined(ESP32) || defined(ESPWifiManualSetup) // for nodemcu, weemos and esp8266 #define wifi_ssid "wifi ssid" #define wifi_password "wifi password" #else // for arduino + W5100 const byte mac[] = { 0xDE, 0xED, 0xBA, 0xFE, 0x54, 0x95 }; //W5100 ethernet shield mac adress #endif #define WifiManager_password "your_password" //this is going to be the WPA2-PSK password for the initial setup access point #define WifiManager_ssid "OpenMQTTGateway" //this is the network name of the initial setup access point /*-------------DEFINE YOUR MQTT PARAMETERS BELOW----------------*/ //MQTT Parameters definition //#define mqtt_server_name "www.mqtt_broker.com" // instead of defining the server by its IP you can define it by its name, uncomment this line and set the correct MQTT server host name char mqtt_user[20] = "your_username"; // not compulsory only if your broker needs authentication char mqtt_pass[30] = "your_password"; // not compulsory only if your broker needs authentication char mqtt_server[40] = "192.168.1.17"; char mqtt_port[6] = "1883"; #define Gateway_Name "OpenMQTTGateway" //uncomment the line below to integrate msg value into the subject when receiving //#define valueAsASubject true /*-------------DEFINE THE MODULES YOU WANT BELOW----------------*/ //Addons and module management, comment the Z line #define ZgatewayRF "RF" //ESP8266, Arduino, ESP32 //#define ZgatewayRF315 "RF315" //ESP8266, Arduino, ESP32 #define ZgatewayIR "IR" //ESP8266, Arduino, Sonoff RF Bridge //#define ZgatewayPilight "Pilight" //ESP8266, Arduino, ESP32 #define ZgatewayBT "BT" //ESP8266, Arduino, ESP32 //#define ZgatewayRF2 "RF2" //ESP8266, Arduino, ESP32 //#define ZgatewaySRFB "SRFB" // Sonoff RF Bridge //#define Zgateway2G "2G" //ESP8266, Arduino, ESP32 //#define ZactuatorONOFF "ONOFF" //ESP8266, Arduino, ESP32, Sonoff RF Bridge //#define ZsensorINA226 "INA226" //ESP8266, Arduino, ESP32 //#define ZsensorHCSR501 "HCSR501" //ESP8266, Arduino, ESP32, Sonoff RF Bridge //#define ZsensorADC "ADC" //ESP8266, Arduino, ESP32 //#define ZsensorBH1750 "BH1750" //ESP8266, Arduino, ESP32 //#define ZsensorTSL2561 "TSL2561" //ESP8266, Arduino, ESP32 //#define ZsensorBME280 "BME280" //ESP8266, Arduino, ESP32 //#define ZsensorDHT "DHT" //ESP8266, Arduino, ESP32, Sonoff RF Bridge //#define ZgatewayRFM69 "RFM69" //ESP8266, Arduino, ESP32 //#define ZsensorGPIOKeyCode "GPIOKeyCode" //ESP8266, Arduino, ESP32 //#define ZsensorGPIOInput "GPIOInput" //ESP8266, Arduino, ESP32 #define ZmqttDiscovery "HADiscovery"//ESP8266, Arduino, EPS32, Sonoff RF Bridge /*-------------DEFINE YOUR ADVANCED NETWORK PARAMETERS BELOW----------------*/ //#define MDNS_SD //uncomment if you want to use mdns for discovering automatically your ip server, please note that MDNS with ESP32 can cause the BLE to not work //#define cleanFS true //uncomment if you want to clean the ESP memory and reenter your credentials #define maxMQTTretry 4 //maximum MQTT connection attempts before going to wifi setup //set minimum quality of signal so it ignores AP's under that quality #define MinimumWifiSignalQuality 8 // these values are only used if no dhcp configuration is available const byte ip[] = { 192, 168, 1, 99 }; //ip adress const byte gateway[] = { 0, 0, 0, 0 }; //ip adress, if first value is different from 0 advanced config network will be used and you should fill gateway & dns const byte Dns[] = { 0, 0, 0, 0 }; //ip adress, if first value is different from 0 advanced config network will be used and you should fill gateway & dns const byte subnet[] = { 255, 255, 255, 0 }; //ip adress /*-------------DEFINE YOUR MQTT ADVANCED PARAMETERS BELOW----------------*/ #define Base_Topic "home/" #define version_Topic Base_Topic Gateway_Name "/version" #define will_Topic Base_Topic Gateway_Name "/LWT" #define will_QoS 0 #define will_Retain true #define will_Message "offline" #define Gateway_AnnouncementMsg "online" #define jsonPublishing true //comment if you don't want to use Json publishing (one topic for all the parameters) //example home/OpenMQTTGateway_ESP32_DEVKIT/BTtoMQTT/4XXXXXXXXXX4 {"rssi":-63,"servicedata":"fe0000000000000000000000000000000000000000"} //#define simplePublishing true //comment if you don't want to use simple publishing (one topic for one parameter) //example // home/OpenMQTTGateway_ESP32_DEVKIT/BTtoMQTT/4XXXXXXXXXX4/rssi -63.0 // home/OpenMQTTGateway_ESP32_DEVKIT/BTtoMQTT/4XXXXXXXXXX4/servicedata fe0000000000000000000000000000000000000000 /*-------------DEFINE YOUR OTA PARAMETERS BELOW----------------*/ #define ota_hostname Gateway_Name #define ota_password "OTAPASSWORD" #define ota_port 8266 /*-------------DEFINE PINs FOR STATUS LEDs----------------*/ #define led_receive 40 #define led_send 42 #define led_error 44 // VCC ------------D|-----------/\/\/\/\ ----------------- Arduino PIN // LED Resistor 270-510R /*----------------------------OTHER PARAMETERS-----------------------------*/ /*-------------------CHANGING THEM IS NOT COMPULSORY-----------------------*/ /*----------------------------USER PARAMETERS-----------------------------*/ #ifdef ZgatewaySRFB #define SERIAL_BAUD 19200 #else #define SERIAL_BAUD 115200 #endif /*--------------MQTT general topics-----------------*/ // global MQTT subject listened by the gateway to execute commands (send RF, IR or others) #define subjectMQTTtoX Base_Topic Gateway_Name "/commands/#" #define subjectMultiGTWKey "toMQTT" #define subjectGTWSendKey "MQTTto" //variables to avoid duplicates #define time_avoid_duplicate 3000 // if you want to avoid duplicate mqtt message received set this to > 0, the value is the time in milliseconds during which we don't publish duplicates //uncomment to use multicore function of ESP32 for BLE #ifdef ESP32 #define multiCore //comment to don't use multicore function of ESP32 for BLE #endif #define JSON_MSG_BUFFER 512 // Json message max buffer size, don't put 1024 or higher it is causing unexpected behaviour on ESP8266 #define TimeBetweenReadingSYS 120000 // time between system readings (like memory) #define subjectSYStoMQTT Base_Topic Gateway_Name "/SYStoMQTT" /*-------------------ACTIVATE TRACES----------------------*/ #define TRACE 1 // commented = trace off, uncommented = trace on