* Add Wifi manager web portal for ESP8266
#15#83
* represent web page if MQTT failures at start
* add arduinojson library on CI and repo
* add parameter in test config for CI and correct ifdef
* add wifi manager library
* add possibility to manual setup esp8266 wifi credential
* add mqtt user and password into wifimanager
* Add MinimumWifiSignalQuality parameter
Following @ctripodi suggestion to remove AP with low signal quality
* globally expose repeat functionality as advanced function
* implement repeated sends for Arduino based boards
* use String class instead of C-style arrays to benefit from dynamic allocation and avoid buffer overflows. Try to improve stability of BME280.
* replace sprintf with String class to avoid buffer overruns by dynamic allocation
* fix caps on variable
* re-add TSL2561 code that was accidentally removed
* esp32 init
* RF gateway ok with ESP32
* correct IR gateway compilation errors and test RF2 ok
* divide config per board type
* update test file according user_config
* differentiate variable type following IR libraries aka platforms
* implement BLE beacons detection with ESP32
* Implement multitasking on BLE gateway
* Library add and change core assignement
* change core assignement for BLE
* add mi flora value readings with ESP32
* adding some traces and removing unecessary comment
* correct compilation error due to pin assignement
* correct temperature float value and wrong mac adress rssi publishing
* add esp32 to CI
* correct esp32 ide retrieving
* correcting paths
* CI: correct architecture
* libraries update (irremote) and overwrite ble library files
* Add suport for presenting status with 3 LEDs
* Add support for presenting status with 3 LEDs
* Update Test_config.h
* Update User_config.h
Better names for LED variables
* Change names for LED variables
* Add support for TSL2561 based light intensity measurement
* replace Serial prints with trc, add TSL2561 code to test config
* add Adafruit TSL2561 lib to Travis config
* avoid multiple definitions and fix missing string constructor in trace
When not using advanced network config, the ip is optained via DHCP, so display it after the connection is established. Output was 0.0.0.0 in this case before.
Also adding display of the mac for mac address filter config in the wifi-ap.
* Made rf2 sending and receiving work
With code from https://github.com/1technophile/OpenMQTTGateway/pull/109
plus some other fixes.
* Added support for group bit
Added support for sending and receiving group bit
* Group bit and MQTT retransmitting
Added support for sending and receiving group bit.
Made the gateway transmit the new state of a RF2 switch to the MQTT state topic when it receives a MQTT command to control that switch.
* Removed hard coded RF2 code length
* Added support for dimming to RF2
Verified to work with Nexa WMR-250 dimmer.
* Minor cleanup
* some minor correction after coadcy checks
* Put serial communication speed as a parameter in user_config.h
* complete gateway file
receiving ok
sending ko
#32
* add rfm69 to CI
* change receiver key and minor improvments
#32
now ok on receiving and sending with RFM69
* add schema and tested pinout for RFM69/RF/IR wiring
#32
* RFM69 library add
* Implement newremoteswitchlibrary for KlikAanKlikUit / ClickOnClickOff protocol
#3
* add dependency for CI and link to the library
* compilation error for arduino correction
* Sketch size decrease
* remove nano from CI
* Divide user_config into one file per gateway/sensor for lisibility
* some minor correction after coadcy checks
* Put serial communication speed as a parameter in user_config.h
* complete gateway file
receiving ok
sending ko
#32
* add rfm69 to CI
* change receiver key and minor improvments
#32
now ok on receiving and sending with RFM69
* add schema and tested pinout for RFM69/RF/IR wiring
#32
* RFM69 library add
* Implement newremoteswitchlibrary for KlikAanKlikUit / ClickOnClickOff protocol
#3
* add dependency for CI and link to the library
* compilation error for arduino correction
* Sketch size decrease
* remove nano from CI
* some minor correction after coadcy checks
* Put serial communication speed as a parameter in user_config.h
* complete gateway file
receiving ok
sending ko
#32
* add rfm69 to CI
* change receiver key and minor improvments
#32
now ok on receiving and sending with RFM69
* add schema and tested pinout for RFM69/RF/IR wiring
#32
* RFM69 library add
* changed user config
* added lightsensor module
* changed Pin Adresses
* Added I2C Lightsensor
Added the I2C Lightsensor and Switchted most Pins
* removed some debug to serial
removed some debug stuff was send to serial console
* Merge with Master
* Too much things for arduino uno
per default remove sensors for it
* Adding I2C Module function
Opens the Door on OpenMQTTGateway for "i2c Bus Modules/Sensors"
* Fixing BH1750 detection
Fixing the detection for a missing BH1750 Module
* Add libraries and define sensors depending on wiring type #63
Florian