[DOCS] Overhaul new-user onboarding, home page, and upload flow (#2347)

Getting started:
- New 15-minute Getting Started guide featuring the two most popular
  tracks (BLE on esp32dev-ble, RF on lilygo-rtl_433), with broker setup
  and a verification step
- Sidebar restructured around the new-user journey; upload options
  numbered by ease; Gitpod upload method removed

Home page:
- VitePress hero with clear actions, larger hero image
- How-it-works pipeline diagram shared as a component (responsive via
  container queries), use-case grid, bigger video tiles without the
  image lightbox, refreshed press coverage list, functions pills
- Support section pointing to Theengs Bridge and
  github.com/sponsors/1technophile

Upload flow:
- Decision-oriented upload landing page (journey strip, method cards,
  comparison table)
- Pre-flight checklist and driver troubleshooting on the web installer
- Guided environment picker (bridge + hardware wizard) replacing the
  filter chips, with manifest-verified recommendations
- Post-flash next-steps card linking to the portal and verification

Board images:
- custom_img key in environments.ini and board photos for all
  web-flashable environments (licenses recorded); private prod_env.ini
  environments excluded from boards-info.json

Corrections:
- RF frequency coverage stated as 433/315/868/915MHz
- Removed references to the retired compatible.openmqttgateway.com
  site (BLE list is decoder.theengs.io), the discontinued Theengs
  Plug, and the private sponsor forum


Claude-Session: https://claude.ai/code/session_01TYysQW8tpmt1dWWuzKhTLi

Co-authored-by: Florian <1technophile@users.noreply.github.com>
Co-authored-by: Claude Fable 5 <noreply@anthropic.com>

docs/setitup/actuators.md

@@ -1,11 +1,11 @@
 # Actuators
 ## Compatible parts 
-|Module|Purpose|Where to Buy|
-|-|-|-|
-|LED|Basic led|-|
-|FASTLED|RGB Leds management|-|
-|BUZZER|-|-|
-|RELAY|Switch power circuit|-|
+|Module|Purpose|
+|-|-|
+|LED|Basic led|
+|FASTLED|RGB Leds management|
+|BUZZER|-|
+|RELAY|Switch power circuit|
 
 ## Pinout
 |Module| Boards|

docs/setitup/gsm.md

@@ -1,10 +1,10 @@
 # GSM 2G gateway
 ## Compatible parts
 
-|Module|Purpose|Where to Buy|
-|-|-|-|
-|A6|GSM GPRS module|-|
-|A7|GSM GPRS module with GPS|-|
+|Module|Purpose|
+|-|-|
+|A6|GSM GPRS module|
+|A7|GSM GPRS module with GPS|
 
 ## Hardware setup
 

docs/setitup/ir.md

@@ -1,12 +1,12 @@
 # IR gateway
 ## Compatible parts
-|Module|Purpose|Where to Buy|
-|-|-|-|
-|IR diode|Emitting|-|
-|IR receiver|Receiving|-|
-|transistor 2N2222|Amplify uC signal for the IR diode|-|
-|330 ohms resistor|-|-|
-|220 ohms resistor|limit current to LED|-|
+|Module|Purpose|
+|-|-|
+|IR diode|Emitting|
+|IR receiver|Receiving|
+|transistor 2N2222|Amplify uC signal for the IR diode|
+|330 ohms resistor|-|
+|220 ohms resistor|limit current to LED|
 
 The IR setup can work with bc547 and a 4x3 LED-Matrix.
 

docs/setitup/rf.md

@@ -1,4 +1,4 @@
-# RF gateway (433mhz/315mhz)
+# RF gateway (433/315/868/915MHz)
 
 ## Protocols, modules and library
 
@@ -21,13 +21,13 @@ If you want to try the RTL_433 module with a combination or a board outside of t
 Heltec LORA V3 is not compatible with RTL_433 library as it is based on an SX1262 module.
 
 ## Assembly/soldering required parts
-|Module|Purpose|Compatible modules|Receiver Switching|Where to Buy|
-|-|-|-|-|-|
-|SRX882 or SRX882S (recommended)|433Mhz Receiver|RF(RCSwitch), RF2(KaKu), Pilight|Supported|-|
-|STX882 (recommended)|433Mhz Transmitter|RF(RCSwitch), RF2(KaKu), Pilight|Supported|-|
-|CC1101|433Mhz Transceiver|[RTL_433](../use/rf#supported-decoders), RF(RCSwitch), RF2(KaKu), Pilight|Supported|-|
-|SX1276/SX1278|433Mhz Transceiver|[RTL_433](../use/rf#supported-decoders)|Not Supported|-|
-|LilyGo/Heltec|433Mhz Transceiver|[RTL_433](../use/rf#supported-decoders)|Not Supported|-|
+|Module|Purpose|Compatible modules|Receiver Switching|
+|-|-|-|-|
+|SRX882 or SRX882S (recommended)|433Mhz Receiver|RF(RCSwitch), RF2(KaKu), Pilight|Supported|
+|STX882 (recommended)|433Mhz Transmitter|RF(RCSwitch), RF2(KaKu), Pilight|Supported|
+|CC1101|433Mhz Transceiver|[RTL_433](../use/rf#supported-decoders), RF(RCSwitch), RF2(KaKu), Pilight|Supported|
+|SX1276/SX1278|433Mhz Transceiver|[RTL_433](../use/rf#supported-decoders)|Not Supported|
+|LilyGo/Heltec|433Mhz Transceiver|[RTL_433](../use/rf#supported-decoders)|Not Supported|
 
 ### SRX STX Pinout
 |Board| Receiver Pin| Emitter Pin|
@@ -72,9 +72,9 @@ When **all** these variables are defined, OpenMQTTGateway will use your custom p
 ![Addon_RF](../img/OpenMQTTgateway_ESP32_Addon_RF.png)
 
 ## ESP8266 Hardware setup
-The default receiver pin is D2 (gpio 4). Avoid D3 (gpio 0): it is a boot strapping pin, a receiver holding it low at reset forces the ESP8266 into flash mode and the board never starts.
+If the gateway works only when serial monitor is connected don't use D3 use D2 instead (gpio 4) and modify config_RF.h accordingly.
 
-With SRX882 some users reported issues on D2, use D1 instead in this case and modify config_RF.h accordingly.
+With SRX882 some users reported that D3 is not working use D1 instead in this case and modify config_RF.h accordingly.
 
 ![Addon_RF](../img/OpenMQTTgateway_ESP8266_Addon_RF.png)
 

docs/setitup/sensors.md

@@ -1,21 +1,21 @@
 # Sensors
 ## Compatible sensors
-|Module|Purpose|Where to Buy|
-|-|-|-|
-|DHT11|Temperature, Humidity|-|
-|DHT22|Temperature, Humidity|-|
-|HCSR501|PIR|-|
-|BH1750|Digital light|-|
-|BME280|Temperature, Humidity, Pressure|-|
-|BMP280|Temperature, Pressure|-|
-|C-37, YL-83, HM-RD|Leak, Water|-|
-|HTU21|Temperature, Humidity|-|
-|GPIO Input|Inputs|-|
-|GPIO KeyCode|Keycode|-|
-|INA226|Current, Voltage|-|
-|MQ2|Gas (flammable)|-|
-|TEMT6000|Luminosity|-|
-|TSL2561|Luminosity|-|
+|Module|Purpose|
+|-|-|
+|DHT11|Temperature, Humidity|
+|DHT22|Temperature, Humidity|
+|HCSR501|PIR|
+|BH1750|Digital light|
+|BME280|Temperature, Humidity, Pressure|
+|BMP280|Temperature, Pressure|
+|C-37, YL-83, HM-RD|Leak, Water|
+|HTU21|Temperature, Humidity|
+|GPIO Input|Inputs|
+|GPIO KeyCode|Keycode|
+|INA226|Current, Voltage|
+|MQ2|Gas (flammable)|
+|TEMT6000|Luminosity|
+|TSL2561|Luminosity|
 
 ## Pinout
 |Module|Arduino Pin| ESP8266 Pin|ESP32 Pin|