publish libraries to avoid users to have to download them one by one
This commit is contained in:
1technophile committed
1 parent
93c075e880
commit
f0546fab8c
396 files changed
+536928
No files matched your search
@@ -0,0 +1,181 @@
|
||||
/******************************************************************************
|
||||
LCD_DeltaAltitude.ino
|
||||
BME280 Arduino and Teensy example
|
||||
Marshall Taylor @ SparkFun Electronics
|
||||
Oct 19, 2015
|
||||
https://github.com/sparkfun/SparkFun_BME280_Arduino_Library
|
||||
|
||||
This sketch configures a BME280 to measure height changes, with a button
|
||||
to zero.
|
||||
|
||||
Hardware connections:
|
||||
BME280 -> Arduino
|
||||
GND -> GND
|
||||
3.3 -> 3.3
|
||||
SDA -> A4
|
||||
SCL -> A5
|
||||
|
||||
Button (Normally open) between A4 and A5.
|
||||
|
||||
LCD:
|
||||
* LCD RS pin to digital pin 7
|
||||
* LCD Enable pin to digital 6
|
||||
* LCD D4 pin to digital pin 5
|
||||
* LCD D5 pin to digital pin 4
|
||||
* LCD D6 pin to digital pin 3
|
||||
* LCD D7 pin to digital pin 2
|
||||
* LCD R/W pin to ground
|
||||
* 10K resistor:
|
||||
* ends to +5V and ground
|
||||
* wiper to LCD VO pin (pin 3)
|
||||
|
||||
To use, run the sketch, then press and hold the button until the data on the
|
||||
serial monitor shows zero. Then, move the sensor to a new altitude and watch
|
||||
how the output changes!
|
||||
|
||||
Note: For most accurate results keep the sensor orientation and temperature the
|
||||
same between measurements.
|
||||
|
||||
Resources:
|
||||
Uses Wire.h for I2C operation
|
||||
Uses SPI.h for SPI operation
|
||||
Included CircularBuffer class for averaging
|
||||
|
||||
Development environment specifics:
|
||||
Arduino IDE 1.6.4
|
||||
Teensy loader 1.23
|
||||
|
||||
This code is released under the [MIT License](http://opensource.org/licenses/MIT).
|
||||
Please review the LICENSE.md file included with this example. If you have any questions
|
||||
or concerns with licensing, please contact techsupport@sparkfun.com.
|
||||
Distributed as-is; no warranty is given.
|
||||
******************************************************************************/
|
||||
|
||||
#include <stdint.h>
|
||||
#include "SparkFunBME280.h"
|
||||
#include "CircularBuffer.h"
|
||||
|
||||
#include "Wire.h"
|
||||
#include "SPI.h"
|
||||
#include <LiquidCrystal.h>
|
||||
|
||||
//Global sensor object
|
||||
BME280 mySensor;
|
||||
uint8_t buttonGroundPin = A0;
|
||||
uint8_t buttonSensePin = A2;
|
||||
|
||||
CircularBuffer myBuffer(50);
|
||||
//int icounter = 0;
|
||||
float reference = 0;
|
||||
|
||||
LiquidCrystal lcd(7,6,5,4,3,2);
|
||||
|
||||
void setup()
|
||||
{
|
||||
//Configure the button IO
|
||||
pinMode( buttonSensePin, INPUT_PULLUP );
|
||||
pinMode( buttonGroundPin, OUTPUT );
|
||||
digitalWrite( buttonGroundPin, 0 );
|
||||
|
||||
//***Driver settings********************************//
|
||||
//commInterface can be I2C_MODE or SPI_MODE
|
||||
//specify chipSelectPin using arduino pin names
|
||||
//specify I2C address. Can be 0x77(default) or 0x76
|
||||
|
||||
//For I2C, enable the following and disable the SPI section
|
||||
mySensor.settings.commInterface = I2C_MODE;
|
||||
mySensor.settings.I2CAddress = 0x77;
|
||||
|
||||
//For SPI enable the following and dissable the I2C section
|
||||
//mySensor.settings.commInterface = SPI_MODE;
|
||||
//mySensor.settings.chipSelectPin = 10;
|
||||
|
||||
|
||||
//***Operation settings*****************************//
|
||||
|
||||
//renMode can be:
|
||||
// 0, Sleep mode
|
||||
// 1 or 2, Forced mode
|
||||
// 3, Normal mode
|
||||
mySensor.settings.runMode = 3; //Forced mode
|
||||
|
||||
//tStandby can be:
|
||||
// 0, 0.5ms
|
||||
// 1, 62.5ms
|
||||
// 2, 125ms
|
||||
// 3, 250ms
|
||||
// 4, 500ms
|
||||
// 5, 1000ms
|
||||
// 6, 10ms
|
||||
// 7, 20ms
|
||||
mySensor.settings.tStandby = 0;
|
||||
|
||||
//filter can be off or number of FIR coefficients to use:
|
||||
// 0, filter off
|
||||
// 1, coefficients = 2
|
||||
// 2, coefficients = 4
|
||||
// 3, coefficients = 8
|
||||
// 4, coefficients = 16
|
||||
mySensor.settings.filter = 4;
|
||||
|
||||
//tempOverSample can be:
|
||||
// 0, skipped
|
||||
// 1 through 5, oversampling *1, *2, *4, *8, *16 respectively
|
||||
mySensor.settings.tempOverSample = 5;
|
||||
|
||||
//pressOverSample can be:
|
||||
// 0, skipped
|
||||
// 1 through 5, oversampling *1, *2, *4, *8, *16 respectively
|
||||
mySensor.settings.pressOverSample = 5;
|
||||
|
||||
//humidOverSample can be:
|
||||
// 0, skipped
|
||||
// 1 through 5, oversampling *1, *2, *4, *8, *16 respectively
|
||||
mySensor.settings.humidOverSample = 0;
|
||||
|
||||
Serial.begin(57600);
|
||||
Serial.print("Program Started\n");
|
||||
Serial.print("Starting BME280... result of .begin(): 0x");
|
||||
//Calling .begin() causes the settings to be loaded
|
||||
delay(10);//Needs > 2 ms to start up
|
||||
Serial.println(mySensor.begin(), HEX);
|
||||
|
||||
Serial.println();
|
||||
|
||||
lcd.begin(16, 2);
|
||||
|
||||
lcd.clear();
|
||||
|
||||
}
|
||||
|
||||
void loop()
|
||||
{
|
||||
//Get the local temperature! Do this for calibration
|
||||
mySensor.readTempC();
|
||||
|
||||
//Check button. No debounce, so hold for operation
|
||||
if( digitalRead( buttonSensePin ) == 0 )
|
||||
{
|
||||
//Set reference altitude.
|
||||
reference = mySensor.readFloatAltitudeFeet();
|
||||
}
|
||||
|
||||
float lastAlt = mySensor.readFloatAltitudeFeet() - reference;
|
||||
myBuffer.pushElement(lastAlt);
|
||||
float tempAlt = myBuffer.averageLast(8); //Do an average of the latest samples
|
||||
|
||||
lcd.setCursor(0,0);
|
||||
lcd.print("Altitude: ");
|
||||
|
||||
myBuffer.pushElement(lastAlt);
|
||||
|
||||
lcd.setCursor(0,1);
|
||||
if(tempAlt >= 0)
|
||||
{
|
||||
lcd.print(" ");
|
||||
}
|
||||
lcd.print(tempAlt);
|
||||
lcd.print(" ft ");
|
||||
delay(200);
|
||||
|
||||
}
|
||||
Reference in new issue
Block a user