Update IRRemoteESP8266 version to 2.5.5

factorize IR send signal function between the 2 types of receiving
Add new IRRemoteESP8266 protocols
replace pins on mega according schema
remove unecessaries spaces

lib/IRremoteESP8266/examples/IRGCSendDemo/IRGCSendDemo.ino

@@ -24,12 +24,13 @@
  *     have enough current to drive the IR LED effectively.
  *   * Make sure you have the IR LED polarity correct.
  *     See: https://learn.sparkfun.com/tutorials/polarity/diode-and-led-polarity
- *   * Typical digital camera/phones can be used to see if the IR LED is flashed.
- *     Replace the IR LED with a normal LED if you don't have a digital camera
- *     when debugging.
+ *   * Typical digital camera/phones can be used to see if the IR LED is
+ * flashed. Replace the IR LED with a normal LED if you don't have a digital
+ * camera when debugging.
  *   * Avoid using the following pins unless you really know what you are doing:
  *     * Pin 0/D3: Can interfere with the boot/program mode & support circuits.
- *     * Pin 1/TX/TXD0: Any serial transmissions from the ESP8266 will interfere.
+ *     * Pin 1/TX/TXD0: Any serial transmissions from the ESP8266 will
+ * interfere.
  *     * Pin 3/RX/RXD0: Any serial transmissions to the ESP8266 will interfere.
  *   * ESP-01 modules are tricky. We suggest you use a module with more GPIOs
  *     for your first time. e.g. ESP-12 etc.
@@ -45,11 +46,11 @@
 // These codes can be found in GC's Control Tower database.
 
 uint16_t Samsung_power_toggle[71] = {
-    38000, 1, 1, 170, 170, 20, 63, 20, 63, 20, 63, 20, 20, 20, 20, 20, 20, 20,
-    20, 20, 20, 20, 63, 20, 63, 20, 63, 20, 20, 20, 20, 20, 20, 20, 20, 20, 20,
-    20, 20, 20, 63, 20, 20, 20, 20, 20, 20, 20, 20, 20, 20, 20, 20, 20, 63, 20,
-    20, 20, 63, 20, 63, 20, 63, 20, 63, 20, 63, 20, 63, 20, 1798};
-
+    38000, 1,  1,  170, 170, 20, 63, 20, 63, 20, 63,  20, 20, 20, 20,
+    20,    20, 20, 20,  20,  20, 20, 63, 20, 63, 20,  63, 20, 20, 20,
+    20,    20, 20, 20,  20,  20, 20, 20, 20, 20, 63,  20, 20, 20, 20,
+    20,    20, 20, 20,  20,  20, 20, 20, 20, 63, 20,  20, 20, 63, 20,
+    63,    20, 63, 20,  63,  20, 63, 20, 63, 20, 1798};
 
 #define IR_LED 4  // ESP8266 GPIO pin to use. Recommended: 4 (D2).
 
@@ -64,7 +65,7 @@ void loop() {
   Serial.println("Toggling power");
 #if SEND_GLOBALCACHE
   irsend.sendGC(Samsung_power_toggle, 71);
-#else  // SEND_GLOBALCACHE
+#else   // SEND_GLOBALCACHE
   Serial.println("Can't send because SEND_GLOBALCACHE has been disabled.");
 #endif  // SEND_GLOBALCACHE
   delay(10000);