[SYS] Extend Wifi mode and power change to ESP8266 (#1680)

Extend Wifi mode and power change to ESP8266
 (Fix the spelling of setESPWifiProtocolTxPower)

docs/use/boards.md

@@ -13,12 +13,12 @@ On M5Stack boards you may do a long press to these buttons in low power mode 0 (
 
 You can also do a long press when powering the board to reset it, this press must be done during the first 5 seconds after the start.
 
-### WiFi interference on ESP32 ###
+### Wifi interference on sensors when using an ESP ###
-Certain sensors like HC-SR501 is prone to generate false signals / triggers when used on a ESP32 with WiFi enabled. To reduce or eliminate the effect the board must be put into WiFi B/G with lower TX power.
+Certain sensors like HC-SR501 is prone to generate false signals / triggers when used on a ESP with Wifi enabled. To reduce or elimate the effect the board must be put into Wifi B/G with lower TX power.
 
-This can be achieved with the following macro, `WifiGMode` defined true and `WifiPower` to e.g. WIFI_POWER_11dBm.  
+This can be achieved with the following macro, `WifiGMode` defined true and `WifiPower` to e.g. WIFI_POWER_11dBm (ESP32) or 11 (ESP8266).  
 
-Since the WiFi protocol is persisted in the flash of the ESP32 you have to run at least once with `WiFiGMode` defined **false** to get Band N back.
+Since the WiFi protocol is persisted in the flash of the ESP you have to run at least once with `WiFiGMode` defined **false** to get Band N back.
 
 ### Low power mode for ESP32
 OpenMQTTGateway support a low power mode for ESP32, this mode is available per default on boards with batteries. The other boards needs to have the macro `DEFAULT_LOW_POWER_MODE` defined at 0, 1 or 2 to use it. More information about the modes is available into User_config.h.

environments.ini

@@ -1059,6 +1059,8 @@ build_flags =
   '-DsimplePublishing=true'
   '-DGateway_Name="OMG_ESP8266_ALL"'
   '-DDEEP_SLEEP_IN_US=120000000'
+  '-DWifiGMode=true'
+  '-DWifiPower=11'
 board_build.flash_mode = dout
 
 [env:nodemcuv2-fastled-test]

main/User_config.h

@@ -688,18 +688,17 @@ Adafruit_NeoPixel leds2(ANEOPIX_IND_NUM_LEDS, ANEOPIX_IND_DATA_GPIO2, ANEOPIX_IN
 #  define LOG_LEVEL LOG_LEVEL_NOTICE
 #endif
 
-/*-------------------ESP32 Wifi band and tx power ---------------------*/
+/*-------------------ESP Wifi band and tx power ---------------------*/
-//Certain sensors are sensitive to ESP32 Wifi which can cause interference with their normal operation
+//Certain sensors are sensitive to Wifi which can cause interference with their normal operation
 //For example it can cause false triggers on a PIR HC-SR501
 //It is reccomended to change Wifi BAND to G and reduce tx power level to 11dBm
-//Since the WiFi protocol is persisted in the flash of the ESP32 you have to run at least once with `WiFiGMode` defined false to get Band N back.
+//Since the WiFi protocol is persisted in the flash of the ESP you have to run at least once with `WiFiGMode` defined false to get Band N back.
-#ifdef ESP32
 #ifndef WifiGMode
 //#    define WifiGMode                 true
 #endif
 #ifndef WifiPower
-//#    define WifiPower                 WIFI_POWER_11dBm
+//#    define WifiPower                 WIFI_POWER_11dBm //When using an ESP32
-#  endif
+//#    define WifiPower                 11 //When using an ESP8266
 #endif
 
 /*-----------PLACEHOLDERS FOR WebUI DISPLAY--------------*/

main/main.ino

@@ -722,7 +722,7 @@ void callback(char* topic, byte* payload, unsigned int length) {
 }
 
 #if defined(ESP32) && (defined(WifiGMode) || defined(WifiPower))
-void setESP32WifiPorotocolTxPower() {
+void setESPWifiProtocolTxPower() {
   //Reduce WiFi interference when using ESP32 using custom WiFi mode and tx power
   //https://github.com/espressif/arduino-esp32/search?q=WIFI_PROTOCOL_11G
   //https://www.letscontrolit.com/forum/viewtopic.php?t=671&start=20
@@ -763,6 +763,48 @@ void setESP32WifiPorotocolTxPower() {
 }
 #endif
 
+#if defined(ESP8266) && (defined(WifiGMode) || defined(WifiPower))
+void setESPWifiProtocolTxPower() {
+#  if WifiGMode == true
+  if (!wifi_set_phy_mode(PHY_MODE_11G)) {
+    Log.error(F("Failed to change WifiMode." CR));
+  }
+#  endif
+
+#  if WifiGMode == false
+  if (!wifi_set_phy_mode(PHY_MODE_11N)) {
+    Log.error(F("Failed to change WifiMode." CR));
+  }
+#  endif
+
+  phy_mode_t getprotocol = wifi_get_phy_mode();
+  if (getprotocol == PHY_MODE_11N) {
+    Log.notice(F("WiFi_Protocol_11n" CR));
+  }
+  if (getprotocol == PHY_MODE_11G) {
+    Log.notice(F("WiFi_Protocol_11g" CR));
+  }
+  if (getprotocol == PHY_MODE_11B) {
+    Log.notice(F("WiFi_Protocol_11b" CR));
+  }
+
+#  ifdef WifiPower
+  Log.notice(F("Requested WiFi power level: %i dBm" CR), WifiPower);
+
+  int i_dBm = int(WifiPower * 4.0f);
+
+  // i_dBm 82 == 20.5 dBm
+  if (i_dBm > 82) {
+    i_dBm = 82;
+  } else if (i_dBm < 0) {
+    i_dBm = 0;
+  }
+
+  system_phy_set_max_tpw((uint8_t)i_dBm);
+#  endif
+}
+#endif
+
 void setup() {
   //Launch serial for debugging purposes
   Serial.begin(SERIAL_BAUD);
@@ -1088,8 +1130,8 @@ bool wifi_reconnect_bypass() {
     Log.notice(F("Attempting Wifi connection with saved AP: %d" CR), wifi_autoreconnect_cnt);
 
     WiFi.begin();
-#  if defined(ESP32) && (defined(WifiGMode) || defined(WifiPower))
+#  if (defined(ESP8266) || defined(ESP32)) && (defined(WifiGMode) || defined(WifiPower))
-    setESP32WifiPorotocolTxPower();
+    setESPWifiProtocolTxPower();
 #  endif
     delay(1000);
     wifi_autoreconnect_cnt++;
@@ -2492,8 +2534,8 @@ void MQTTtoSYS(char* topicOri, JsonObject& SYSdata) { // json object decoding
 
       Log.warning(F("Attempting connection to new AP %s" CR), (const char*)SYSdata["wifi_ssid"]);
       WiFi.begin((const char*)SYSdata["wifi_ssid"], (const char*)SYSdata["wifi_pass"]);
-#  if defined(ESP32) && (defined(WifiGMode) || defined(WifiPower))
+#  if (defined(ESP8266) || defined(ESP32)) && (defined(WifiGMode) || defined(WifiPower))
-      setESP32WifiPorotocolTxPower();
+      setESPWifiProtocolTxPower();
 #  endif
       WiFi.waitForConnectResult();
 
@@ -2501,8 +2543,8 @@ void MQTTtoSYS(char* topicOri, JsonObject& SYSdata) { // json object decoding
         Log.error(F("Failed to connect to new AP; falling back" CR));
         WiFi.disconnect(true);
         WiFi.begin(prev_ssid.c_str(), prev_pass.c_str());
-#  if defined(ESP32) && (defined(WifiGMode) || defined(WifiPower))
+#  if (defined(ESP8266) || defined(ESP32)) && (defined(WifiGMode) || defined(WifiPower))
-        setESP32WifiPorotocolTxPower();
+        setESPWifiProtocolTxPower();
 #  endif
       }
       ESPRestart(7);