diff --git a/docs/use/sensors.md b/docs/use/sensors.md
index b7216aa..02813cd 100644
--- a/docs/use/sensors.md
+++ b/docs/use/sensors.md
@@ -12,9 +12,6 @@ You will receive every TimeBetweenReadingDHT (set into config_DHT.h) the DHT mea
`home/OpenMQTTGateway/DHTtoMQTT {"tempc":21,"tempf":69.8,"hum":51}`
-Legacy (removed after release 0.9.5)
-`home/OpenMQTTGateway/DHTtoMQTT {"temp":21,"hum":51}`
-
If you want to don't resend value when it is the same you can set dht_always = false in config_DHT.h
### HTU21
@@ -37,9 +34,6 @@ Each sensor will be published under the following topic using each sensors' addr
`home/OpenMQTTGateway/CLIMAtoMQTT/ds1820/0x0000000000000000 {"tempc":27.8, "tempf":82.04, "type":"DS18B20","res":"12bit\n","addr":"0x28616411907650bc"}`
-Legacy (removed after release 0.9.5)
-`home/OpenMQTTGateway/CLIMAtoMQTT/ds1820/0x0000000000000000 {"temp":27.8,"unit":"C","type":"DS18B20","res":"12bit\n","addr":"0x28616411907650bc"}`
-
The units for temperature readings are sent in Celsius by default can be changed to Fahrenheit by setting DS1820_FAHRENHEIT = true in in config_DS1820.h
If you don't want to resend values that haven't changed you can set DS1820_ALWAYS = false in config_DS1820.h
@@ -55,4 +49,9 @@ This can be useful if you would like to connect an LED to turn on when motion is
`#define HCSR501_LED_NOTIFY_GPIO 4`
This notification pin can be inverted if driving directly or through a transistor/mosfet.
-`#define INVERT_LED_NOTIFY true`
\ No newline at end of file
+`#define INVERT_LED_NOTIFY true`
+
+### RN8209
+You will receive every TimeBetweenReadingRN8209 (set into config_RN8209.h) the RN8209 measurements (10s per default).
+
+`home/OpenMQTTGateway/RN8209toMQTT {"volt":120.345,"current":7.9264,"power":954.6132}`
diff --git a/main/ZgatewayBT.ino b/main/ZgatewayBT.ino
index 553a3c7..1a24ecf 100644
--- a/main/ZgatewayBT.ino
+++ b/main/ZgatewayBT.ino
@@ -328,8 +328,6 @@ void emptyBTQueue() {
}
}
-bool ProcessLock = false; // Process lock when we want to use a critical function like OTA for example
-
void createOrUpdateDevice(const char* mac, uint8_t flags, int model, int mac_type = 0);
BLEdevice* getDeviceByMac(const char* mac); // Declared here to avoid pre-compilation issue (misplaced auto declaration by pio)
diff --git a/main/ZmqttDiscovery.ino b/main/ZmqttDiscovery.ino
index db58e51..7eb8329 100644
--- a/main/ZmqttDiscovery.ino
+++ b/main/ZmqttDiscovery.ino
@@ -758,6 +758,29 @@ void pubMqttDiscovery() {
);
# endif
+# ifdef ZsensorRN8209
+# define RN8209parametersCount 3
+ Log.trace(F("RN8209Discovery" CR));
+ char* RN8209sensor[RN8209parametersCount][8] = {
+ {"sensor", "volt", "RN8209", "", jsonVolt, "", "", "V"},
+ {"sensor", "current", "RN8209", "", jsonCurrent, "", "", "A"},
+ {"sensor", "power", "RN8209", "", jsonPower, "", "", "W"}
+ //component type,name,availability topic,device class,value template,payload on, payload off, unit of measurement
+ };
+
+ for (int i = 0; i < RN8209parametersCount; i++) {
+ String name = String(RN8209sensor[i][2]) + "PWR: " + String(RN8209sensor[i][1]);
+ createDiscovery(RN8209sensor[i][0],
+ subjectRN8209toMQTT, (char*)name.c_str(), (char*)getUniqueId(RN8209sensor[i][1], RN8209sensor[i][2]).c_str(),
+ will_Topic, RN8209sensor[i][3], RN8209sensor[i][4],
+ RN8209sensor[i][5], RN8209sensor[i][6], RN8209sensor[i][7],
+ 0, "", "", true, "",
+ "", "", "", "", false, // device name, device manufacturer, device model, device MAC, retain
+ stateClassNone //State Class
+ );
+ }
+# endif
+
# ifdef ZgatewayRF
// Sensor to display RF received value
Log.trace(F("gatewayRFDiscovery" CR));
diff --git a/main/ZsensorRN8209.ino b/main/ZsensorRN8209.ino
new file mode 100644
index 0000000..4cb2113
--- /dev/null
+++ b/main/ZsensorRN8209.ino
@@ -0,0 +1,83 @@
+/*
+ OpenMQTTGateway Addon - ESP8266, ESP32 or Arduino program for home automation
+
+ Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker
+ Send and receiving command by MQTT
+
+ RN8209 reading Addon
+
+ Contributors:
+ - 1technophile
+
+ This file is part of OpenMQTTGateway.
+
+ OpenMQTTGateway is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+ OpenMQTTGateway is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program. If not, see .
+*/
+#ifdef ZsensorRN8209
+
+# include "ArduinoJson.h"
+# include "driver/uart.h"
+# include "rn8209_flash.h"
+# include "rn8209c_user.h"
+
+extern "C" bool init_8209c_interface();
+
+StaticJsonDocument doc;
+
+void rn8209_loop(void* mode) {
+ if (!ProcessLock) {
+ uint32_t voltage;
+ int32_t current;
+ int32_t power;
+
+ while (1) {
+ rn8209c_read_voltage(&voltage);
+ uint8_t ret = rn8209c_read_emu_status();
+ if (ret) {
+ uint32_t temp_current = 0;
+ uint32_t temp_power = 0;
+ rn8209c_read_current(phase_A, &temp_current);
+ rn8209c_read_power(phase_A, &temp_power);
+ if (ret == 1) {
+ current = temp_current;
+ power = temp_power;
+ } else {
+ current = (int32_t)temp_current * (-1);
+ power = (int32_t)temp_power * (-1);
+ }
+ }
+
+ JsonObject data = doc.to();
+ data["volt"] = (float)voltage / 1000.0;
+ data["current"] = (float)current / 10000.0;
+ data["power"] = (float)power / 10000.0;
+ pub(subjectRN8209toMQTT, data);
+ delay(TimeBetweenReadingRN8209);
+ }
+ } else {
+ Log.trace(F("RN8209 reading canceled by processLock" CR));
+ }
+}
+
+void setupRN8209() {
+ STU_8209C cal = {0};
+ cal.Ku = RN8209_KU;
+ cal.Kia = RN8209_KIA;
+ cal.EC = RN8209_EC;
+ set_user_param(cal);
+ init_8209c_interface();
+ xTaskCreate(rn8209_loop, "rn8209_loop", RN8209_TASK_STACK_SIZE, NULL, RN8209_TASK_PRIO, NULL);
+}
+
+#endif // ZsensorRN8209
\ No newline at end of file
diff --git a/main/config_RN8209.h b/main/config_RN8209.h
new file mode 100644
index 0000000..92541fe
--- /dev/null
+++ b/main/config_RN8209.h
@@ -0,0 +1,49 @@
+/*
+ OpenMQTTGateway - ESP8266 or Arduino program for home automation
+
+ Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal and a MQTT broker
+ Send and receiving command by MQTT
+
+ This files enables to set your parameter for the RN8209 sensor
+
+ Copyright: (c)Florian ROBERT
+
+ This file is part of OpenMQTTGateway.
+
+ OpenMQTTGateway is free software: you can redistribute it and/or modify
+ it under the terms of the GNU General Public License as published by
+ the Free Software Foundation, either version 3 of the License, or
+ (at your option) any later version.
+
+ OpenMQTTGateway is distributed in the hope that it will be useful,
+ but WITHOUT ANY WARRANTY; without even the implied warranty of
+ MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ GNU General Public License for more details.
+
+ You should have received a copy of the GNU General Public License
+ along with this program. If not, see .
+*/
+#ifndef config_RN8209_h
+#define config_RN8209_h
+
+extern void setupRN8209();
+extern void RN8209toMQTT();
+/*----------------------------USER PARAMETERS-----------------------------*/
+/*-------------DEFINE YOUR MQTT PARAMETERS BELOW----------------*/
+#define subjectRN8209toMQTT "/RN8209toMQTT"
+
+/*-------------CALIBRATION PARAMETERS----------------*/
+#ifndef RN8209_KU
+# define RN8209_KU 18570
+#endif
+#ifndef RN8209_KIA
+# define RN8209_KIA 272433
+#endif
+#ifndef RN8209_EC
+# define RN8209_EC 28250
+#endif
+
+#ifndef TimeBetweenReadingRN8209
+# define TimeBetweenReadingRN8209 10000 // time between 2 RN8209 readings in ms
+#endif
+#endif
diff --git a/main/main.ino b/main/main.ino
index 615a9a4..c4b223e 100644
--- a/main/main.ino
+++ b/main/main.ino
@@ -120,6 +120,9 @@ struct GfSun2000Data {};
#ifdef ZsensorAHTx0
# include "config_AHTx0.h"
#endif
+#ifdef ZsensorRN8209
+# include "config_RN8209.h"
+#endif
#ifdef ZsensorHCSR04
# include "config_HCSR04.h"
#endif
@@ -210,6 +213,8 @@ static String ota_server_cert = "";
# include
# include
+bool ProcessLock = false; // Process lock when we want to use a critical function like OTA for example
+
# ifdef ESP32_ETHERNET
# include
void WiFiEvent(WiFiEvent_t event);
@@ -863,6 +868,10 @@ void setup() {
# endif
# define ACTIVE_RECEIVER ACTIVE_RTL
#endif
+#ifdef ZsensorRN8209
+ setupRN8209();
+ modules.add(ZsensorRN8209);
+#endif
#if defined(ZgatewayRTL_433) || defined(ZgatewayRF) || defined(ZgatewayPilight) || defined(ZgatewayRF2)
# ifdef DEFAULT_RECEIVER // Allow defining of default receiver as a compiler directive
activeReceiver = DEFAULT_RECEIVER;
diff --git a/platformio.ini b/platformio.ini
index bd46c42..79b44dd 100644
--- a/platformio.ini
+++ b/platformio.ini
@@ -141,6 +141,7 @@ gfSunInverter = https://github.com/BlackSmith/GFSunInverter.git#v1.0.1
decoder = https://github.com/theengs/decoder.git#v0.9.7
ssd1306 = thingpulse/ESP8266 and ESP32 OLED driver for SSD1306 displays@^4.3.0
lm75 = jeremycole/I2C Temperature Sensors derived from the LM75@^1.0.3
+rn8209 = https://github.com/theengs/RN8209C-SDK.git#arduino
[env]
framework = arduino
@@ -265,6 +266,7 @@ lib_deps =
${libraries.dallastemperature}
${libraries.rfWeatherStation}
${libraries.shtc3}
+ ${libraries.rn8209}
build_flags =
${com-esp.build_flags}
'-DZgatewayRF="RF"'
@@ -289,6 +291,7 @@ build_flags =
'-DZgatewayRFM69="RFM69"'
'-DZsensorGPIOInput="GPIOInput"'
'-DZsensorGPIOKeyCode="GPIOKeyCode"'
+ '-DZsensorRN8209="RN8209"'
'-DZgatewayWeatherStation="WeatherStation"'
'-DsimplePublishing=true'
'-DWM_PWD_FROM_MAC=true'