Platformio integration (#424)

* adaptation of structure to platformio

* also remove zgatewayRF315 (not usefull)

* replace boolean by bool

#155

main/config_RFM69.h

@@ -0,0 +1,79 @@
+/*
+  OpenMQTTGateway  - ESP8266 or Arduino program for home automation
+
+   Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal  and a MQTT broker
+   Send and receiving command by MQTT
+
+   This files enables to set your parameter for the radiofrequency gateways (ZgatewayRF and ZgatewayRF2) with RCswitch and newremoteswitch library
+
+    Copyright: (c)Florian ROBERT
+
+    This file is part of OpenMQTTGateway.
+
+    OpenMQTTGateway is free software: you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation, either version 3 of the License, or
+    (at your option) any later version.
+
+    OpenMQTTGateway is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+#ifndef config_RFM69_h
+#define config_RFM69_h
+
+extern void setupRFM69();
+extern bool RFM69toMQTT();  
+extern void MQTTtoRFM69(char * topicOri, char * datacallback);
+extern void MQTTtoRFM69(char * topicOri, JsonObject& RFdata);
+/*----------------------RFM69 topics & parameters -------------------------*/
+// Topic where the message from RFM69 will be published by the gateway,
+// appended with the nodeID of the sender
+#define subjectRFM69toMQTT  Base_Topic Gateway_Name "/RFM69toMQTT"
+
+// Topic subscribed by the gateway. Messages received will be sent to RFM69
+#define subjectMQTTtoRFM69  Base_Topic Gateway_Name "/commands/MQTTtoRFM69"
+#define RFM69receiverKey "RCV_" // receiver id will be defined if a subject contains RFM69receiverKey followed by a value of 3 digits
+// On reception of an ack from RFM69, the message that has been sent is published here
+#define subjectGTWRFM69toMQTT  Base_Topic Gateway_Name "/RFM69toMQTT/acked"
+#define defaultRFM69ReceiverId 99
+
+// Default values
+const char PROGMEM ENCRYPTKEY[] = "sampleEncryptKey";
+const char PROGMEM MDNS_NAME[] = "rfm69gw1";
+const char PROGMEM MQTT_BROKER[] = "raspi2";
+const char PROGMEM RFM69AP_NAME[] = "RFM69-AP";
+#define NETWORKID     200  //the same on all nodes that talk to each other
+#define NODEID        10
+
+//Match frequency to the hardware version of the radio
+#define FREQUENCY     RF69_433MHZ
+//#define FREQUENCY     RF69_868MHZ
+//#define FREQUENCY      RF69_915MHZ
+#define IS_RFM69HCW    true // set to 'true' if you are using an RFM69HCW module
+#define POWER_LEVEL    31
+
+/*-------------------PIN DEFINITIONS----------------------*/
+#if defined(ESP8266)
+  #define RFM69_CS      D1
+  #define RFM69_IRQ     D8   // GPIO15/D8
+  #define RFM69_IRQN    digitalPinToInterrupt(RFM69_IRQ)
+  #define RFM69_RST     D4   // GPIO02/D4
+#elif defined(ESP32)
+  #define RFM69_CS      1
+  #define RFM69_IRQ     8   // GPIO15/D8
+  #define RFM69_IRQN    digitalPinToInterrupt(RFM69_IRQ)
+  #define RFM69_RST     4   // GPIO02/D4
+#else
+  //RFM69 not tested with arduino
+  #define RFM69_CS      10
+  #define RFM69_IRQ     0
+  #define RFM69_IRQN    digitalPinToInterrupt(RFM69_IRQ)
+  #define RFM69_RST     9
+#endif
+
+#endif