[SYS] Update arduino core to 3.1.1 + refactor ino to cpp (#2177)

* Update arduino core to 3.1.1

* Fix Blufi build

* Update arduinojson, fix build errors with idf

* Fix narrowing

* fix RF builds

* WIP-Convert ino files to cpp

* Fix pilight build

* Fix Somfy actuator build.

* Update esp32dev-rf partition

* Fix Weatherstation build

* Fix GFSunInverter build

* Fix esp32dev-ir build

* Fix ble-aws build

* Fix eth builds

* Fix m5Stack missing pins_arduino.h

* Fix build errors for M5 stack/tough, others are upstream issues.

* Fix RTL 433 build - remaining errors are from radolib

* Fix nodemcu build

* fix 2g builds

* Fix serial build

* Fix actuator on off builds

* Fix SSD1306 build - remaining errors are from radiolib

* Fix multiple definition of OTAserver_cert

* Fix nodemcu rf2 build

* Fix ADC builds

* Fix sensor builds

* Fix LORA builds

* Fix multi-receiver builds - remaining errors are in radiolib

* Fix fastled builds

* Fix theegns board builds

* Fix broker builds

* Update fastled - old version failed all-test build

* Fix RN8209 builds

* Fix max temp actuator builds

* Fix PWM builds

* Fix C37 sensor builds

* Fix HTU21 builds

* Fix INA266 builds

* Fix undefined variables in mqtt discovery

* Fix webui build

* Fix fastled invalid pin error

* Fix wifi manual setup builds

* Fix onewire/all-test build - bin too big error remaining

* Fix theengs plug build

* Fix rfbridge builds

* Fix blufi builds

* Fix undefined functions in serial

* Fix preprocessor definition checks

* Set IDF log level to erre

* Add delay in loop to prevent watchdog timeout

* Use xTaskCreateUniveral to support single core processors

* Remove old HTTPUpdate files - upsteam fixed.

* Cleanup and move common declarations to header file

* Use custom partiton table to fix builds where bin is too large

* Update M5StickC - fixs esp32-m5stick-c-ble build

* Revert to Arduino core 2.x for builds with incompatible libs

* Remove "Z" from file names and rename omg_common to TheengsCommon

* Fix gateway name when using MAC with new Arduino core

* Update IDF config to reduce loop task stack use

* Update esp-nimble-cpp version, corrects BLE uppercase ID's

* Update wifi manager to fix watchdog timeout error

main/config_RF.h

@@ -26,8 +26,7 @@
 #ifndef config_RF_h
 #define config_RF_h
 
-#include <Arduino.h>
-#include <ArduinoJson.h>
+#include "TheengsCommon.h"
 
 #ifdef ZgatewayRF
 extern void setupRF();
@@ -47,14 +46,10 @@ extern void enableRF2Receive();
 #ifdef ZgatewayPilight
 extern void setupPilight();
 extern void PilighttoX();
-extern void XtoPilight(const char* topicOri, const char* datacallback);
-extern void XtoPilight(const char* topicOri, JsonObject& RFdata);
 extern void disablePilightReceive();
 extern void enablePilightReceive();
 #endif
 #ifdef ZgatewayRTL_433
-#  include <rtl_433_ESP.h>
-rtl_433_ESP rtl_433;
 
 extern void RTL_433Loop();
 extern void setupRTL_433();
@@ -217,7 +212,19 @@ struct RFConfig_s {
 #define ACTIVE_RTL      3
 #define ACTIVE_RF2      4
 
-RFConfig_s RFConfig;
+#ifdef ZgatewayRF
+#  define ACTIVE_RECEIVER ACTIVE_RF
+#elif defined(ZgatewayRF2)
+#  define ACTIVE_RECEIVER ACTIVE_RF2
+#elif defined(ZgatewayPilight)
+#  define ACTIVE_RECEIVER ACTIVE_PILIGHT
+#elif defined(ZgatewayRTL_433)
+#  define ACTIVE_RECEIVER ACTIVE_RTL
+#else
+#  define ACTIVE_RECEIVER ACTIVE_NONE
+#endif
+
+extern RFConfig_s RFConfig;
 
 /*-------------------CC1101 DefaultTXPower----------------------*/
 //Adjust the default TX-Power for sending radio if ZradioCC1101 is used.
@@ -230,7 +237,7 @@ RFConfig_s RFConfig;
 #ifndef RF_RECEIVER_GPIO
 #  ifdef ESP8266
 #    define RF_RECEIVER_GPIO 0 // D3 on nodemcu // put 4 with rf bridge direct mod
-#  elif ESP32
+#  elif defined(ESP32)
 #    define RF_RECEIVER_GPIO 27 // D27 on DOIT ESP32
 #  endif
 #endif
@@ -238,7 +245,7 @@ RFConfig_s RFConfig;
 #ifndef RF_EMITTER_GPIO
 #  ifdef ESP8266
 #    define RF_EMITTER_GPIO 3 // RX on nodemcu if it doesn't work with 3, try with 4 (D2) // put 5 with rf bridge direct mod
-#  elif ESP32
+#  elif defined(ESP32)
 #    define RF_EMITTER_GPIO 12 // D12 on DOIT ESP32
 #  else
 //IMPORTANT NOTE: On arduino UNO connect IR emitter pin to D9 , comment #define IR_USE_TIMER2 and uncomment #define IR_USE_TIMER1 on library <library>IRremote/boarddefs.h so as to free pin D3 for RF RECEIVER PIN