User config division (#97)

* some minor correction after coadcy checks

* Put serial communication speed as a parameter in user_config.h

* complete gateway file

receiving ok
sending ko
#32

* add rfm69 to CI

* change receiver key and minor improvments

#32

now ok on receiving and sending with RFM69

* add schema and tested pinout for RFM69/RF/IR wiring

#32

* RFM69 library add

* Implement newremoteswitchlibrary for KlikAanKlikUit / ClickOnClickOff protocol

#3

* add dependency for CI and link to the library

* compilation error for arduino correction

* Sketch size decrease

* remove nano from CI

* Divide user_config into one file per gateway/sensor for lisibility

config_RFM69.h

@@ -0,0 +1,68 @@
+/*  
+  OpenMQTTGateway  - ESP8266 or Arduino program for home automation 
+
+   Act as a wifi or ethernet gateway between your 433mhz/infrared IR signal  and a MQTT broker 
+   Send and receiving command by MQTT
+ 
+   This files enables to set your parameter for the radiofrequency gateways (ZgatewayRF and ZgatewayRF2) with RCswitch and newremoteswitch library
+  
+    Copyright: (c)Florian ROBERT
+  
+    This file is part of OpenMQTTGateway.
+    
+    OpenMQTTGateway is free software: you can redistribute it and/or modify
+    it under the terms of the GNU General Public License as published by
+    the Free Software Foundation, either version 3 of the License, or
+    (at your option) any later version.
+
+    OpenMQTTGateway is distributed in the hope that it will be useful,
+    but WITHOUT ANY WARRANTY; without even the implied warranty of
+    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+    GNU General Public License for more details.
+
+    You should have received a copy of the GNU General Public License
+    along with this program.  If not, see <http://www.gnu.org/licenses/>.
+*/
+
+/*----------------------RFM69 topics & parameters -------------------------*/
+#define subjectRFM69toMQTT "home/RFM69toMQTT"
+#define subjectRFM69toMQTTrssi "home/RFM69toMQTT/rssi"
+#define subjectRFM69toMQTTsender "home/RFM69toMQTT/sender"
+#define subjectMQTTtoRFM69 "home/commands/MQTTtoRFM69"
+#define RFM69receiverKey "RCV_" // receiver id will be defined if a subject contains RFM69receiverKey followed by a value of 3 digits
+#define subjectGTWRFM69toMQTT "home/RFM69toMQTT"
+#define defaultRFM69ReceiverId 99
+
+// Default values
+const char PROGMEM ENCRYPTKEY[] = "sampleEncryptKey";
+const char PROGMEM MDNS_NAME[] = "rfm69gw1";
+const char PROGMEM MQTT_BROKER[] = "raspi2";
+const char PROGMEM RFM69AP_NAME[] = "RFM69-AP";
+#define NETWORKID     200  //the same on all nodes that talk to each other
+#define NODEID        10
+
+//Match frequency to the hardware version of the radio
+#define FREQUENCY     RF69_433MHZ
+//#define FREQUENCY     RF69_868MHZ
+//#define FREQUENCY      RF69_915MHZ
+#define IS_RFM69HCW    true // set to 'true' if you are using an RFM69HCW module
+#define POWER_LEVEL    31
+
+/*-------------------PIN DEFINITIONS----------------------*/
+
+#ifdef RFM69_Wiring // Without Support for I2C Modules and HM10 or 11
+  
+  #ifdef ESP8266
+    #define RFM69_CS      D1  // GPIO5/HCS/D1
+    #define RFM69_IRQ     D8   // GPIO15/D8
+    #define RFM69_IRQN    digitalPinToInterrupt(RFM69_IRQ)
+    #define RFM69_RST     D4   // GPIO02/D4
+  #else
+    //RFM69 not tested with arduino
+    #define RFM69_CS      10
+    #define RFM69_IRQ     2
+    #define RFM69_IRQN    digitalPinToInterrupt(RFM69_IRQ)
+    #define RFM69_RST     9
+  #endif
+#endif
+